Audio & Video

The QSC SC-444 is a THX-approved four-way behind-the-screen cinema loudspeaker in QSC's SC-400 (Digital Cinema Sound) series, and the flagship of the range. It combines a quad-15-inch low-frequency section (four 15-inch woofers) with a coaxial mid/high/very-high assembly for maximum output and extended top-end detail in the largest premium and immersive auditoriums. It supports tri-amplified or quad-amplified operation.Key FeaturesTHX-approved four-way screen channel loudspeaker (flagship...

The QSC SL-DAN-64-P is a perpetual software-based Dante license that adds 64x64 channels of Dante audio networking to a compatible Q-SYS core. Instead of installing a Dante hardware card, integrators enable native Dante transport in software, letting the core send and receive up to 64 channels in each direction with Dante-enabled devices. This is a feature license, not a physical product, and expands interoperability in mixed Q-SYS/Dante systems.Key FeaturesPerpetual software-based Dante...

The QSC SL-QSE-110-P is a Q-SYS Scripting Engine feature license for the Core 110f processor. It is a software license rather than a physical product, unlocking the Q-SYS Scripting Engine so integrators can run Lua-based custom logic and control on that Core. It is activated through the Q-SYS licensing system.Key FeaturesEnables the Q-SYS Scripting Engine on a Core 110fSupports Lua-based custom control and automation logicPerpetual license tied to the specified Core modelSoftware feature...

The QSC SL-QUD-110-P is a Q-SYS UCI Deployment feature license for the Core 110f processor. It is a software license, not a physical product, that unlocks the ability to deploy User Control Interfaces (UCIs) to compatible Q-SYS user control devices from that Core. It is delivered and activated through the Q-SYS licensing system.Key FeaturesEnables UCI (User Control Interface) deployment from a Core 110fPerpetual license tied to the specified Core modelSoftware feature license—no hardware...

The QSC SP-16x is a threaded loudspeaker pole extension used to raise a top-mounted speaker higher above a subwoofer or pole-mount base. It adds roughly 16 inches (about 41 cm) of height on a standard 35 mm diameter shaft, letting integrators and rental crews fine-tune the vertical position of a full-range cabinet for better sight lines and coverage. It is an accessory only, not a loudspeaker.Key FeaturesThreaded 35 mm diameter speaker pole extensionApproximately 16 in (41 cm) added...

The QSC SP-26 is a 26-inch loudspeaker pole accessory, not a standalone speaker. It is designed to mount a top loudspeaker above a QSC KS-series powered subwoofer (or other pole-cup enclosure), raising the top box to a better listening height for portable and installed PA use. The pole uses a threaded male M20 fitting to lock securely into a matching pole cup.Key Features26-inch (approximately 660 mm) rigid loudspeaker poleMale M20 threaded end for a secure, no-slip connectionDesigned to pair...

The QSC SP-36 is a 36-inch (about 91 cm) threaded loudspeaker pole that mounts a full-range speaker on top of a subwoofer or pole-mount base. Built on a 35 mm diameter shaft with M20 threading, it is used across QSC portable and line-array systems to lift a top cabinet to ear level for cleaner coverage. It is a mounting accessory, not a powered or passive loudspeaker.Key Features36 in (91 cm) threaded speaker pole35 mm shaft with M20 threadPositions a top speaker above a subwoofer or...

The QSC SPA2-200 is a higher-power 2-channel compact installation amplifier for commercial audio applications that need more headroom in a small footprint. It delivers 200W per channel into low-impedance loads and supports 70V/100V distributed lines in bridged mode, all in an energy-efficient half-rack chassis suited to background music and paging systems.Key Features2-channel compact amplifier with 200W per channelDrives 4/8 ohm speakers or 70V/100V lines (bridged mode)Energy Star efficient...

The QSC SPA2-60 is a compact, energy-efficient 2-channel installation amplifier for smaller commercial spaces such as retail, offices, and meeting rooms. Its half-rack chassis fits discreetly above a ceiling or in a small rack, and it supports both low-impedance speakers and 70V/100V distributed lines, making it a flexible workhorse for background music and paging.Key Features2-channel compact amplifier in a lightweight half-rack chassisDrives 4/8 ohm speakers or 70V/100V lines (bridged...

The QSC SPA4-100 is a compact 4-channel installation amplifier that delivers more power per zone for multi-zone commercial audio in a small half-rack chassis. It drives four zones of low-impedance speakers and supports 70V/100V distributed lines in bridged mode, providing flexible, energy-efficient amplification for background music and paging.Key Features4-channel compact amplifier with 100W per channelDrives 4/8 ohm speakers or 70V/100V lines (bridged mode)Energy Star efficient with...

The QSC SPA4-60 is a compact, energy-efficient 4-channel installation amplifier for multi-zone commercial audio in a small half-rack chassis. It drives four zones of low-impedance speakers and supports 70V/100V distributed lines in bridged mode, making it a flexible choice for background music and paging in retail, hospitality, and offices.Key Features4-channel compact amplifier for multi-zone systemsDrives 4/8 ohm speakers or 70V/100V lines (bridged mode)Energy Star efficient with...

The QSC SR-1020 is a two-way cinema surround loudspeaker from QSC's SR-series (Digital Cinema Sound), designed for the side and rear surround arrays of a commercial theater. It uses a 10-inch low-frequency driver with a horn-loaded high-frequency section to give even, wide coverage along auditorium walls. Its axisymmetric 90 by 90 degree pattern makes it easy to space uniformly for smooth surround imaging.Key FeaturesTwo-way cinema surround loudspeaker10-inch low-frequency driver with...

The QSC SR-1030 is a high-output two-way cinema surround loudspeaker from QSC's SR-series (Digital Cinema Sound). It is the higher-sensitivity companion to the SR-1020, pairing a 10-inch low-frequency driver with a horn-loaded high-frequency section for greater output in larger or more demanding surround arrays. Its axisymmetric 90 by 90 degree pattern supports uniform spacing along theater walls for smooth, enveloping surround sound.Key FeaturesHigh-output two-way cinema surround...

The QSC SR-1290 is a high-output two-way cinema surround loudspeaker from QSC's SR-series (Digital Cinema Sound), positioned for immersive-audio surround arrays. It pairs a 10-inch low-frequency driver with a horn-loaded high-frequency section and an axisymmetric 90 by 90 degree pattern, so many units can be spaced uniformly around an auditorium for consistent, enveloping object-based sound. It is a strong choice where higher surround SPL and even coverage are required.Key FeaturesHigh-output...

The QSC SR-1590 is a very-high-output two-way cinema surround loudspeaker from QSC's SR-series (Digital Cinema Sound). It uses a 15-inch coaxial driver, mounting the high-frequency section on the same axis as the low-frequency cone for point-source imaging, and delivers a wide 90 degree conical coverage pattern. Its high sensitivity (about 98 dB) and 4-ohm load make it well suited to large and immersive surround arrays that demand substantial SPL.Key FeaturesVery-high-output two-way cinema...

The QSC SR-5152 is a high-power two-way cinema surround loudspeaker from QSC's SR-series (Digital Cinema Sound). Built around a 15-inch low-frequency woofer with a 3-inch voice coil and a horn-loaded high-frequency section, it is intended for large auditoriums and high-SPL surround arrays where extra power handling and output are needed. It is the surround counterpart to QSC's AP-5152 acoustic-performance loudspeaker.Key FeaturesHigh-power two-way cinema surround loudspeaker15-inch...

The QSC SR-800 is a compact two-way cinema surround loudspeaker from QSC's SR-series (Digital Cinema Sound). Built around an 8-inch low-frequency driver with a horn-loaded high-frequency section, it is sized for smaller rooms and for dense surround arrays where a low-profile enclosure is preferred. It delivers even wall-to-wall coverage for smooth surround imaging in screening rooms and smaller auditoriums.Key FeaturesCompact two-way cinema surround loudspeaker8-inch low-frequency driver with...

The QSC SR-8200 is a two-way cinema surround loudspeaker from QSC's SR-series (Digital Cinema Sound). It combines an 8-inch low-frequency driver with a horn-loaded high-frequency section and provides a roughly 90 degree axisymmetric coverage pattern, so units can be spaced uniformly along auditorium walls for consistent surround imaging. Its compact size suits both smaller rooms and dense immersive surround arrays.Key FeaturesTwo-way cinema surround loudspeaker8-inch low-frequency driver with...

The QSC Subwoofer Caster Kit is a set of add-on caster wheels that lets crews roll a QSC subwoofer into position instead of lifting it. This part is documented as the caster kit for the QSC KLA181 line-array subwoofer, letting a single tech maneuver the heavy cabinet across a stage or venue floor. It is a transport accessory only and does not include a subwoofer or any electronics.Key FeaturesBolt-on caster wheel set for a QSC subwoofer cabinetDocumented fitment for the QSC KLA181...

The QSC TouchMix-30 Pro Dust Cover is a fitted fabric cover that protects the TouchMix-30 Pro digital mixer from dust and debris when the console is installed or stored. It slips over the mixer to keep the control surface and connectors clean between sessions, which is useful for fixed installs and studios where the console stays in place. This is a protective accessory, not a functional part of the mixer.Key FeaturesFitted fabric cover for the TouchMix-30 ProKeeps dust off the control surface...

The QSC TouchMix-30 Pro Tote is a padded carrying bag designed specifically for the TouchMix-30 Pro digital mixer. It protects the console during transport and storage with cushioned sides and a shaped interior that fits the mixer, making it easy for engineers and performers to move the console between gigs and rehearsals. This is a transport accessory for the mixer, not a mixer itself.Key FeaturesPadded tote sized for the TouchMix-30 ProProtects the console during transport and...

The QSC TouchMix-30 Tablet Support Stand (also sold as the TS-1) is an accessory for the QSC TouchMix-30 Pro digital mixer. It is a mounting stand, not electronic gear. The stand attaches to the mixer to hold a tablet at a comfortable viewing angle, letting engineers use QSC's TouchMix wireless control app alongside the mixer's own touchscreen. This makes it easier to run the console from the stage or the audience while keeping the tablet stable and within reach. It is a simple, purpose-built...

The QSC TouchMix-30 Tablet Support Stand (model TS-1) is a purpose-built mounting accessory for the TouchMix-30 Pro compact digital mixer. It is aimed at engineers, musicians, and production crews who want to run the mixer's companion tablet app for wireless remote control while still keeping the mixer's own touchscreen and controls within easy reach. The stand attaches to the TouchMix-30 Pro and holds a tablet at a comfortable, angled viewing position directly above the console.Key...

The QSC TSC-116t-G2 is a tabletop stand accessory for the QSC TSC-116w-G2 11.6-inch Q-SYS touch screen controller, finished in textured black. It lets integrators place the large touch panel on a table, lectern, or desk instead of mounting it in a wall. It is intended for spaces that need a portable or desktop control surface for the 11.6-inch panel.Key FeaturesCast-aluminum tabletop stand with textured black powder-coat finishNon-skid, low-profile base to keep the panel stableRemovable cable...