Touch Devices

The Bluesound Professional CP100 gives staff and guests simple, hands-on control of a Bluesound Professional zone. Its glass face carries illuminated, touch-sensitive controls for volume, play/pause/mute and preset recall, lighting up only as needed.It connects over a single RJ45 cable with PoE power and mounts flush to the wall or into a wide range of international electrical back-boxes.Key FeaturesFive programmable presets for quick source or playlist recallEasy-to-clean glass...

The Bluesound Professional CP200 is a low-profile touchscreen wall controller for commercial spaces. A 4 inch, 720 x 720 glass display gives staff a clear, tailored interface for controlling Bluesound Professional zones.Power and data arrive over one PoE network cable, and the included bracket mounts flush without needing a wall stud.Key FeaturesSharp 720 x 720 capacitive touchscreenGlass surface, slim low-profile designPoE powered over RJ45Stud-free flush-mount bracket includedManufacturer...

The Bluesound Professional CP300 puts the full BluOS Controller app on the wall. Its 8 inch glass touchscreen runs Android 13 with the app pre-installed, so staff get the same browsing and zone control as the mobile app from a fixed, secure panel.It is powered over a single PoE+ network cable, mounts flush with the included bracket, and can be locked with a custom PIN.Key FeaturesLarge 8 inch, 1280 x 800 displayQuad-core processor with 2GB RAM and 16GB storagePoE+ class 4, 25.5WPIN code...

The Blustream REM100 gives users a straightforward way to change sources on a Blustream Multicast video over IP system. Point it at a Multicast receiver and press a numbered button to pull up the matching transmitter, with no control processor or app needed for everyday switching.Blustream's IP250UHD manual describes 40 source buttons, with a secondary mode that remaps them to sources 41 to 80 when source button 1 is held for five seconds. Local IR control covers source selection; advanced...

The Blustream REM44 is the IR remote for Blustream's 4x4 HDBaseT matrix kits. It lets users route sources to displays from the room without reaching for a control app, and makes a handy spare for installs where the original remote has gone missing.Key FeaturesInfrared control of Blustream 4x4 matrix routingListed compatibility: HMXL44-KIT-V2, HMXL44CS-KIT, C44-KITIdeal ApplicationsReplacement remote for existing 4x4 matrix installsSpare remote for multi-room residential systemsEquipment rooms...

The Blustream REM62 is the IR remote for the MFP62 multi-format presentation switcher. Blustream's MFP62 manual describes remote control of source selection across HDMI, DisplayPort, USB-C and VGA inputs, analogue audio embedding or bypass, EDID presets, microphone mixing and master volume, so presenters can run a room without touching the rack.Key FeaturesSource buttons for HDMI 1-3, DisplayPort, USB-C and VGAEmbed and Bypass audio buttonsEDID resolution presetsMic Mix On, Mix Off and Mic...

The Blustream REM72 is the IR remote for the MFP72 multi-format presentation switcher. According to the MFP72 manual, it selects sources for each HDMI output, toggles between matrix switcher and splitter modes, sets fixed output resolutions, and handles audio embed, bypass, mute and volume across the HDMI, coaxial and analogue outputs.Key FeaturesOutput 1 and output 2 source selectionMode button for matrix or splitter operationResolution buttonsEmbed, Bypass, Mute and Volume controlsIdeal...

The Blustream REM88 is the IR remote for Blustream's larger matrix switchers. It covers the Custom Pro 8x8 Hub, the Platinum 6x6 and 8x8 models and the HMXL88-V2, making it a practical spare for multi-zone video systems where users want to switch sources from the room.Key FeaturesInfrared matrix routing controlListed compatibility: Custom Pro 8x8 Hub, Platinum 6x6 and 8x8 variants, HMXL88-V2Ideal ApplicationsMulti-room residential video distributionCommercial and hospitality matrix...

The Blustream REMSW41 is a compact IR remote with four direct input buttons and a scroll button. It ships with the SW21AB-V2 and SW41AB-V2 HDMI switches, and Blustream also lists it for per-zone source control on its 4x4 matrix kits, so a remote can sit in each room to change only that room's display.Key FeaturesDirect input selection 1-4Scroll-through input buttonZone control on compatible 4x4 matricesIdeal ApplicationsReplacement remote for SW21AB-V2 and SW41AB-V2 switchesPer-room zone...

The Lutron PJ2-3BRL-GBL-A02 is a Pico smart remote dedicated to music. Instead of light icons, its five buttons are marked for audio, so anyone in the room can start or pause a Sonos zone, nudge the volume up or down, skip to the next track or step through favorite stations without reaching for a phone. The remote is not a stand-alone Sonos controller: it is added to a Lutron system through a Lutron bridge, and the bridge passes its commands to the Sonos player. Because it runs on a single...

The Lutron PJ2-3BRL-GWH-A02 is a Pico smart remote dedicated to music. Instead of light icons, its five buttons are marked for audio, so anyone in the room can start or pause a Sonos zone, nudge the volume up or down, skip to the next track or step through favorite stations without reaching for a phone. The remote is not a stand-alone Sonos controller: it is added to a Lutron system through a Lutron bridge, and the bridge passes its commands to the Sonos player. Because it runs on a single...

The Lutron PJ2-3BRL-LA-L01R is the classic three-button raise/lower Pico remote in Caséta retail packaging. It gives a room a second point of control for Lutron wireless dimmers and switches without running a single wire: tap the top button for on, the bottom for off, use the arrows to brighten or dim, and press the round center button to recall a favorite light level. Light-bulb icons mark the buttons so guests understand them at a glance. Because the remote is powered by a coin cell and...

The Lutron PJ2-3BRL-WH-F01R is a Pico smart remote marked with fan icons, built to run a ceiling fan from anywhere in the room. It is a companion device: it sends commands to a Lutron wireless fan speed control, such as the Caséta smart fan speed control, which actually switches and regulates the fan motor. The top button turns the fan on, the arrows step the speed up or down, the center button recalls a favorite speed, and the bottom button shuts it off. Because the remote runs on a coin-cell...

The Lutron PJ2-3BRL-WH-L01R is the classic three-button raise/lower Pico remote in Caséta retail packaging. It gives a room a second point of control for Lutron wireless dimmers and switches without running a single wire: tap the top button for on, the bottom for off, use the arrows to brighten or dim, and press the round center button to recall a favorite light level. Light-bulb icons mark the buttons so guests understand them at a glance. Because the remote is powered by a coin cell and...

The Lutron PJ2-P2B-GBL Pico Paddle remote brings wireless control to rooms where a rocker-style look is preferred over the button-style Pico. Its upper and lower paddle halves act as on and off for lights, or open and close for Lutron shades. Paired with a Diva smart dimmer, the on side brings lights to the level set by the dimmer's slider, giving consistent scenes from every location. The remote runs on a coin-cell battery and communicates over Lutron's RF link, so it can create a virtual...

The Lutron PJ2-P2B-GBR Pico Paddle remote brings wireless control to rooms where a rocker-style look is preferred over the button-style Pico. Its upper and lower paddle halves act as on and off for lights, or open and close for Lutron shades. Paired with a Diva smart dimmer, the on side brings lights to the level set by the dimmer's slider, giving consistent scenes from every location. The remote runs on a coin-cell battery and communicates over Lutron's RF link, so it can create a virtual...

The Lutron PJ2-P2B-GGR Pico Paddle remote brings wireless control to rooms where a rocker-style look is preferred over the button-style Pico. Its upper and lower paddle halves act as on and off for lights, or open and close for Lutron shades. Paired with a Diva smart dimmer, the on side brings lights to the level set by the dimmer's slider, giving consistent scenes from every location. The remote runs on a coin-cell battery and communicates over Lutron's RF link, so it can create a virtual...

The Lutron PJ2-P2B-GIV Pico Paddle remote brings wireless control to rooms where a rocker-style look is preferred over the button-style Pico. Its upper and lower paddle halves act as on and off for lights, or open and close for Lutron shades. Paired with a Diva smart dimmer, the on side brings lights to the level set by the dimmer's slider, giving consistent scenes from every location. The remote runs on a coin-cell battery and communicates over Lutron's RF link, so it can create a virtual...

The Lutron PJ2-P2B-GLA is a Pico paddle remote: a slim, battery-powered wireless control shaped like a familiar paddle switch. Pair it with a Lutron smart dimmer or switch and it becomes an extra control point for that light, whether you keep it on a nightstand, carry it from room to room, or mount it on the wall where a second switch should have been. Because it communicates over Lutron's Clear Connect RF, there is no wiring, no neutral and no wallbox needed for handheld use. Pairing can be...

The Lutron PJ2-P2B-GWH is a Pico paddle remote: a slim, battery-powered wireless control shaped like a familiar paddle switch. Pair it with a Lutron smart dimmer or switch and it becomes an extra control point for that light, whether you keep it on a nightstand, carry it from room to room, or mount it on the wall where a second switch should have been. Because it communicates over Lutron's Clear Connect RF, there is no wiring, no neutral and no wallbox needed for handheld use. Pairing can be...

The QSC TSC-116w-G2 is an 11.6-inch wall-mount touch screen controller for the Q-SYS platform, finished in black. Its large, high-resolution display provides a premium control surface for audio, video, lighting, and room automation using custom user interfaces built in Q-SYS Designer. It is aimed at boardrooms, briefing centers, and high-end conference spaces.Key Features11.6-inch IPS capacitive touchscreen at full HD 1920 x 1080, 350 nitsSingle-cable Power over Ethernet (IEEE 802.3af), plus...

The QSC TSC-55w-G2 is a compact 5.5-inch wall-mount touch screen controller for the Q-SYS platform, finished in black. It provides a clean, in-wall control surface for adjusting audio, video, and environmental systems using custom user interfaces designed in Q-SYS Designer. It suits meeting rooms, classrooms, and common areas that need a small, always-available controller.Key Features5.5-inch IPS capacitive touchscreen at 1280 x 720, 400 nitsSingle-cable Power over Ethernet (IEEE 802.3af),...

The QSC TSC-80w-G2 is an 8-inch wall-mount touch screen controller for the Q-SYS platform, finished in black. It offers a larger control surface for driving audio, video, lighting, and room automation through custom user interfaces built in Q-SYS Designer. It is well suited to conference rooms, boardrooms, and classrooms that need a clear, responsive in-wall controller.Key Features8-inch IPS capacitive touchscreen at 1280 x 800, 400 nitsSingle-cable Power over Ethernet (IEEE 802.3af), plus...

The Russound IPK-1 is a single-gang keypad that talks to the audio system over the network. Each keypad is paired to one zone and gives that room straightforward control without opening an app. It has four favorite buttons (press to play, press and hold to store what is playing), skip back and forward, play/pause, volume up/down and power. Holding power sends an All Off command to compatible Russound devices. The volume LEDs light only while volume is being adjusted, and the status LED turns...