Mounts & Racks

The Chief CMSZ006 is a short, fully threaded extension column for Chief's CMS-series 1.5-inch NPT ceiling system. Because the pipe is threaded along its whole length rather than only at the ends, it can be run further into a ceiling plate or mount fitting to close up the gap, giving an effective drop anywhere from zero to six inches. That makes it a practical choice for low ceilings, tight projector throw positions or close-to-ceiling flat panel installs where a standard column would hang the...

The Chief CMSZ006S is a short, fully threaded extension column for Chief's CMS-series 1.5-inch NPT ceiling system. Because the pipe is threaded along its whole length rather than only at the ends, it can be run further into a ceiling plate or mount fitting to close up the gap, giving an effective drop anywhere from zero to six inches. That makes it a practical choice for low ceilings, tight projector throw positions or close-to-ceiling flat panel installs where a standard column would hang the...

The Chief CPA018 is a 18-inch (45.7 cm) extension column for Chief's CPA pin connection ceiling system. CPA columns link a CPA ceiling plate or adapter to a Chief ceiling mount, setting the drop height for heavy flat panels, ceiling-hung video walls and multi-screen menu boards. Install is simple: optionally feed cables through the column, seat it in the CPA ceiling plate and secure it per the plate instructions, then attach the mount to the lower end. Chief rates the column at 500 lbs, but...

The Chief CPA024 is a 24-inch (61 cm) extension column for Chief's CPA pin connection ceiling system. CPA columns link a CPA ceiling plate or adapter to a Chief ceiling mount, setting the drop height for heavy flat panels, ceiling-hung video walls and multi-screen menu boards. Install is simple: optionally feed cables through the column, seat it in the CPA ceiling plate and secure it per the plate instructions, then attach the mount to the lower end. Chief rates the column at 500 lbs, but the...

The Chief CPA036 is a 36-inch (91.4 cm) extension column for Chief's CPA pin connection ceiling system. CPA columns link a CPA ceiling plate or adapter to a Chief ceiling mount, setting the drop height for heavy flat panels, ceiling-hung video walls and multi-screen menu boards. Install is simple: optionally feed cables through the column, seat it in the CPA ceiling plate and secure it per the plate instructions, then attach the mount to the lower end. Chief rates the column at 500 lbs, but...

The Chief CPA048 is a 48-inch (121.9 cm) extension column for Chief's CPA pin connection ceiling system. CPA columns link a CPA ceiling plate or adapter to a Chief ceiling mount, setting the drop height for heavy flat panels, ceiling-hung video walls and multi-screen menu boards. Install is simple: optionally feed cables through the column, seat it in the CPA ceiling plate and secure it per the plate instructions, then attach the mount to the lower end. Chief rates the column at 500 lbs, but...

The Chief CPA048P is a 48-inch (121.9 cm) pre-drilled extension column for Chief's CPA pin connection ceiling system. CPA columns link a CPA ceiling plate or adapter to a Chief ceiling mount, setting the drop height for heavy flat panels, ceiling-hung video walls and multi-screen menu boards. Install is simple: optionally feed cables through the column, seat it in the CPA ceiling plate and secure it per the plate instructions, then attach the mount to the lower end. Chief rates the column at...

The Chief CPA060 is a 60-inch (152.4 cm) extension column for Chief's CPA pin connection ceiling system. CPA columns link a CPA ceiling plate or adapter to a Chief ceiling mount, setting the drop height for heavy flat panels, ceiling-hung video walls and multi-screen menu boards. Install is simple: optionally feed cables through the column, seat it in the CPA ceiling plate and secure it per the plate instructions, then attach the mount to the lower end. Chief rates the column at 500 lbs, but...

The Chief CPA072 is a 72-inch (182.9 cm) extension column for Chief's CPA pin connection ceiling system. CPA columns link a CPA ceiling plate or adapter to a Chief ceiling mount, setting the drop height for heavy flat panels, ceiling-hung video walls and multi-screen menu boards. Install is simple: optionally feed cables through the column, seat it in the CPA ceiling plate and secure it per the plate instructions, then attach the mount to the lower end. Chief rates the column at 500 lbs, but...

The Chief CPA072P is a 72-inch (182.9 cm) pre-drilled extension column for Chief's CPA pin connection ceiling system. CPA columns link a CPA ceiling plate or adapter to a Chief ceiling mount, setting the drop height for heavy flat panels, ceiling-hung video walls and multi-screen menu boards. Install is simple: optionally feed cables through the column, seat it in the CPA ceiling plate and secure it per the plate instructions, then attach the mount to the lower end. Chief rates the column at...

The Chief CPA084 is a 84-inch (213.4 cm) extension column for Chief's CPA pin connection ceiling system. CPA columns link a CPA ceiling plate or adapter to a Chief ceiling mount, setting the drop height for heavy flat panels, ceiling-hung video walls and multi-screen menu boards. Install is simple: optionally feed cables through the column, seat it in the CPA ceiling plate and secure it per the plate instructions, then attach the mount to the lower end. Chief rates the column at 500 lbs, but...

The Chief CPA096 is a 96-inch (243.8 cm) extension column for Chief's CPA pin connection ceiling system. CPA columns link a CPA ceiling plate or adapter to a Chief ceiling mount, setting the drop height for heavy flat panels, ceiling-hung video walls and multi-screen menu boards. Install is simple: optionally feed cables through the column, seat it in the CPA ceiling plate and secure it per the plate instructions, then attach the mount to the lower end. Chief rates the column at 500 lbs, but...

The Chief CPA108 is a 108-inch (274.3 cm) extension column for Chief's CPA pin connection ceiling system. CPA columns link a CPA ceiling plate or adapter to a Chief ceiling mount, setting the drop height for heavy flat panels, ceiling-hung video walls and multi-screen menu boards. Install is simple: optionally feed cables through the column, seat it in the CPA ceiling plate and secure it per the plate instructions, then attach the mount to the lower end. Chief rates the column at 500 lbs, but...

The Chief CPA120 is a 120-inch (304.8 cm) extension column for Chief's CPA pin connection ceiling system. CPA columns link a CPA ceiling plate or adapter to a Chief ceiling mount, setting the drop height for heavy flat panels, ceiling-hung video walls and multi-screen menu boards. Install is simple: optionally feed cables through the column, seat it in the CPA ceiling plate and secure it per the plate instructions, then attach the mount to the lower end. Chief rates the column at 500 lbs, but...

The Chief CPA261 bridges two Chief ceiling-mount systems: the CPA pin connection hardware used by Chief's heavier ceiling, video wall and menu-board mounts, and standard 1.5-inch NPT threaded columns. The adapter has a CPA pin connection on one side and a female 1.5" NPT thread on the other, so a threaded pipe can be used with CPA-based hardware. Chief describes it as a coupler for connecting LCM video wall products to a column with 1.5-inch NPT threads. This is useful when an existing NPT...

The Chief CPA262 lets a Chief CPA pin connection column mate with hardware that uses 1.5-inch NPT threads. One side accepts the CPA column's pin connection and the other carries a male 1.5" NPT thread, which screws into a female-threaded fitting such as an NPT ceiling plate or mount coupler. That gives integrators flexibility to mix Chief's CPA column system with NPT-based components already on site or required by the design. It is the companion to the CPA261, which provides a female NPT...

The Chief CPA263 is a connector coupler for the CPA pin-connection column system. When a single extension column is not long enough to bring a projector or display down to the right height, the CPA263 joins two CPA columns together so they act as one continuous drop. It keeps the system's pin-style connection, so the finished assembly installs the same way as a standard CPA column between a ceiling plate and a mount. Chief rates the coupler to 500 lbs (226.8 kg), lists it as UL Listed and TAA...

The Chief CPA264 is an adapter coupler that bridges threaded pipe and Chief's CPA pin-connection column system. One end is a female NPT thread and the other a female CPA connection, so an installer can join a threaded pipe, column or fitting to CPA columns, ceiling plates or mounts. That makes it handy when an existing threaded drop is already in place, or when a project calls for a mix of standard pipe and Chief CPA components. Chief rates the coupler to 500 lbs (226.8 kg), lists it as UL...

The Chief CPA265 is a projector adapter for the CPA pin-connection column system. It mates Chief RPA, RPM, RSA and RSM projector mounts to cut-to-length CPA columns, so an installer can size the drop on site and still finish with a secure, purpose-built joint. Tension at the connection is adjustable to take out play, and the assembly hardware is included. Chief rates the adapter for a 50 lb (22.7 kg) safe working load and lists it as UL Listed. It is finished in silver. For a tidy look, Chief...

The Chief CPA330 is an offset ceiling plate for the CPA pin-connection system. Its 8-inch square plate stands 1.75 inches off the ceiling, creating a gap that lets power and signal cables exit neatly when the mount is fastened to a flat surface with no access above. Overall height is 3.95 inches. The plate accepts Chief CPA extension columns and also works with LCM and MCM single display ceiling mounts and LCM multi-display ceiling mounts. Chief rates it to 500 lbs (226.8 kg) and lists it as...

The Chief CPA351 is a low-profile collar plate that turns Chief CPA or CMS columns into a floor-to-ceiling pole. It is intended for locations where the ceiling or wall cannot support a display on its own, giving the installation a second anchor at the floor so the structure shares the load. Used at both floor and ceiling, it creates a floor-load-bearing assembly; for a ceiling-load-bearing build, Chief recommends a standard ceiling plate at the top instead. The resulting pole accepts Chief...

The Chief CPA353 is a clamp-style plate for building floor-to-ceiling poles with Chief CPA or CMS columns. Like its low-profile CPA351 sibling, it adds stability where the wall or ceiling cannot support a display installation by itself, carrying the advantages of Chief Fusion ceiling mounts into a free-standing pole format. The CPA353 differs in its clamp design, which offers a larger clamp clearance area around the column. Chief rates the system at 500 lbs (227 kg) per pole and supports...

The Chief CPA365 is a pole and truss adapter for the CPA pin-connection system. Instead of fastening to a flat ceiling, it clamps around round pipe or truss members from 0.75 to 3 inches (19 to 76 mm) outside diameter, giving projector and display mounts a secure attachment point in exposed-structure spaces. It accepts Chief CPA extension columns and also works with LCM and MCM single display ceiling mounts and LCM multi-display ceiling mounts. Chief rates the adapter to 500 lbs (226.8 kg) and...

The Chief CPA380 is a truss clamp that brings the CPA pin-connection column system to 2-inch (51 mm) tube truss. Designed with rental and staging crews in mind, it uses a trigger-style clamp so one person can set it, then accepts any Chief CPA column, accessory or projector and flat panel mount for temporary projection and display needs. Chief rates the clamp for a 250 lb (113.4 kg) safe working load and lists it as TAA compliant. It measures 8.18 x 4.09 x 1.5 inches and is finished in silver....