Mounts & Racks

The Chief CPA395 is an angled ceiling plate for the CPA pin-connection system. It lets installers hang a plumb column from a sloped, pitched or vaulted ceiling, so the projector or display below stays level. Chief lists an adjustment range of -5 to +95 degrees. The plate accepts Chief CPA extension columns and also works with LCM and MCM single display ceiling mounts and LCM multi-display ceiling mounts. Chief rates it to 500 lbs (226.8 kg) and lists it as UL Listed and TAA compliant. The...

The Chief CPA640 is a decorative ceiling tile ring that finishes the opening where a mounting column passes through a suspended-ceiling tile. Cutting a tile for a projector or display drop rarely leaves a perfect edge; this black ring slips over the column and sits against the tile to hide the cut and give the installation a tidy, intentional look. Chief's product listing identifies it for CMS and CPAE columns. It is a trim piece only and carries no load, so the column must still be secured to...

The Chief CPA640W is a decorative ceiling tile ring that finishes the opening where a mounting column passes through a suspended-ceiling tile. Cutting a tile for a projector or display drop rarely leaves a perfect edge; this white ring slips over the column and sits against the tile to hide the cut and give the installation a tidy, intentional look. Chief's product listing identifies it for CMS and CPAE columns. It is a trim piece only and carries no load, so the column must still be secured...

The Chief CSA100 is a device holder made for the ConnexSys video wall mounting system. It hangs straight from the ConnexSys strut channel, putting media players, receivers, extenders and similar components right behind the displays they serve. A slotted plate makes it easy to fasten a wide range of devices with straps or screws, and when used with the LVS1U and LVSXU mounts, a power strip can be attached to the side. The holder measures 9.85 x 7.97 x 1.49 inches (250 x 202 x 38 mm), supports...

The Chief CSACB2 is a two-bracket pack for installations of the CSACK06B side cover kit that need extra connection points to the ConnexSys channel strut. Larger or taller video walls can call for more support along the cover than the kit's included brackets provide; these brackets clip to the strut channel already on the wall, so the cover gains attachment points without drilling more holes into the wall surface. Chief notes the materials support one row of display coverage. The brackets are...

The Chief CSACK06B is a side cover kit that frames the edges of a ConnexSys video wall. Exposed mounts, strut and cables along the perimeter of a wall can undo the clean look of a seamless display array; this kit closes in the sides with covers that attach through included ConnexSys brackets, giving the wall a finished, recessed appearance. Chief's ConnexSys brochure lists it at 6 inches deep by 84 inches long and compatible with all ConnexSys mounts. Where an installation needs additional...

The Chief CSACLIPS are cable quick ties designed for the ConnexSys video wall mounting system. Each tie locks onto the strut channel with a simple quarter turn, giving installers a fast way to anchor power, signal and network runs along the wall without drilling or adhesive. They also keep RapidDraw display release cords in place, so pull cords stay reachable and out of the way. Neat, labeled cable runs make later service and display swaps on the wall faster and easier. Each tie measures 1.38...

The Chief CSAS060 is a 60-inch length of strut channel for the ConnexSys video wall mounting system. Installed horizontally on the wall, the channel serves as the rail that ConnexSys LVS display mounts hang from, and mounts can slide laterally along it so each display lands exactly where the layout requires. Using continuous strut also reduces the number of wall anchors compared with individual wall plates and gives a straight reference line for the whole array. The channel has a 1.65 x 0.84...

The Chief CSAS072 is a 72-inch length of strut channel for the ConnexSys video wall mounting system. Installed horizontally on the wall, the channel serves as the rail that ConnexSys LVS display mounts hang from, and mounts can slide laterally along it so each display lands exactly where the layout requires. Using continuous strut also reduces the number of wall anchors compared with individual wall plates and gives a straight reference line for the whole array. The channel has a 1.65 x 0.84...

The Chief CSAS090 is a 90-inch length of strut channel for the ConnexSys video wall mounting system. Installed horizontally on the wall, the channel serves as the rail that ConnexSys LVS display mounts hang from, and mounts can slide laterally along it so each display lands exactly where the layout requires. Using continuous strut also reduces the number of wall anchors compared with individual wall plates and gives a straight reference line for the whole array. The channel has a 1.65 x 0.84...

The Chief CSMP9X12 is a Proximity component storage panel that keeps small devices close to the display they serve. Its 9 x 12 inch (228 x 304 mm) mounting area accepts media players, codecs, extenders and power supplies, and the panel can be set in a variety of orientations to suit the install. Chief lists compatibility with Middle Atlantic Forward Cable Management solutions, the FCALRB1 display mount accessory and the AVA1101, and shows it as part of complete mobile videoconferencing cart...

The Chief CSPBPTA is a Proximity component storage backplane for Thinstall in-wall swing arm accessories. It fits inside the TA500 or TA501 in-wall box and provides a 28.3 x 13.75 inch (718 x 349 mm) mounting area for media players, extenders, power supplies and other gear that sits behind a display on a Thinstall arm. Because the panel can be loaded at a staging area before it goes into the wall, it suits large, standardized roll-outs where every room should be built the same way. Chief rates...

The Chief CSPH is a Proximity component storage panel designed to mount under conference tables and desks. It gives installers over 350 square inches of attachment area to secure PCs, codecs, switchers, power supplies and cable slack, keeping them off the floor and out of sight. Panels can be loaded at a staging area and then installed at each desk, and once mounted the panel pivots 90 degrees so technicians can reach components in a vertical position. Breakaway sections at one-third and...

The Chief CSPHK is the hinge bracket kit for the Proximity CSPH under-table component storage panel. The CSPH ships without brackets so its breakaway sections can be put to use; the CSPHK mounts a full panel, or the one-third and two-thirds pieces left after breaking one apart, to the underside of a table or desk. Once installed, the panel hinges down 90 degrees so components can be reached in a vertical position, then swings back out of sight. A template is included for accurate bracket...

The Chief CSPR is a removable Proximity component storage panel that mounts on the wall behind or beside a display, independent of the display mount. It offers more than 160 square inches of secure attachment area for media players, PCs, extenders and power supplies. A built-in handle makes it easy to carry, install and lift off the wall, so a technician can pull the panel to service equipment without taking the display down. Panels can be pre-loaded off-site, which helps standardize component...

The Chief CSSLP15X10 is a Proximity series slide-lock storage panel built to put small AV components where nobody sees them: directly behind the display they support. Media players, video extenders, network switches and control processors can be fastened to its removable 15" x 10" Lever Lock plate, then tucked into the space behind the screen. When the gear needs attention, the panel slides out for access and locks back in when you are done, so technicians are not forced to pull the display...

The Chief D1UB-NA is a USB charging hub designed as an add-on for the Koncis single monitor arm. Rather than running a separate charger across the work surface, the hub press-fits to the arm so phones, tablets and other USB-powered devices can be topped up right where the user sits. Chief rates it at 18 watts with a 3 amp output. The housing is only 0.88 inches tall and measures 0.88" x 4.77" x 4.77" overall, keeping a clean, low profile on the desk. It is finished in black to match the DMA1B...

The Chief D1US-NA is a USB charging hub designed as an add-on for the Koncis single monitor arm. Rather than running a separate charger across the work surface, the hub press-fits to the arm so phones, tablets and other USB-powered devices can be topped up right where the user sits. Chief rates it at 18 watts with a 3 amp output. The housing is only 0.88 inches tall and measures 0.88" x 4.77" x 4.77" overall, keeping a clean, low profile on the desk. It is finished in silver to match the DMA1S...

The Chief D2UB-NA is a USB charging hub designed as an add-on for the Koncis dual monitor arm. Rather than running a separate charger across the work surface, the hub press-fits to the arm so phones, tablets and other USB-powered devices can be topped up right where the user sits. Chief rates it at 18 watts with a 3 amp output. The housing is only 0.88 inches tall and measures 0.88" x 10.27" x 4.27" overall, keeping a clean, low profile on the desk. It is finished in black to match the DMA2B...

The Chief D2US-NA is a USB charging hub designed as an add-on for the Koncis dual monitor arm. Rather than running a separate charger across the work surface, the hub press-fits to the arm so phones, tablets and other USB-powered devices can be topped up right where the user sits. Chief rates it at 18 watts with a 3 amp output. The housing is only 0.88 inches tall and measures 0.88" x 10.27" x 4.27" overall, keeping a clean, low profile on the desk. It is finished in silver to match the DMA2S...

The Chief DMA1B is a Koncis single dynamic monitor arm that lets users place one monitor exactly where they work best. Designed for desk and tabletop installation, the arm provides height adjustment, extension and swivel so screens can be pulled closer for detail work or pushed back to free up surface space. Chief's Extreme Tilt Technology gives an unusually wide +65° / -10° tilt range, which makes it easy to angle a screen for sharing, standing use or glare control. Height Assist balances the...

The Chief DMA1S is a Koncis single dynamic monitor arm that lets users place one monitor exactly where they work best. Designed for desk and tabletop installation, the arm provides height adjustment, extension and swivel so screens can be pulled closer for detail work or pushed back to free up surface space. Chief's Extreme Tilt Technology gives an unusually wide +65° / -10° tilt range, which makes it easy to angle a screen for sharing, standing use or glare control. Height Assist balances the...

The Chief DMA2B is a Koncis dual dynamic monitor arm that lets users place two monitors exactly where they work best. Designed for desk and tabletop installation, the arm provides height adjustment, extension and swivel so screens can be pulled closer for detail work or pushed back to free up surface space. Chief's Extreme Tilt Technology gives an unusually wide +65° / -10° tilt range, which makes it easy to angle a screen for sharing, standing use or glare control. Height Assist balances the...

The Chief DMA2S is a Koncis dual dynamic monitor arm that lets users place two monitors exactly where they work best. Designed for desk and tabletop installation, the arm provides height adjustment, extension and swivel so screens can be pulled closer for detail work or pushed back to free up surface space. Chief's Extreme Tilt Technology gives an unusually wide +65° / -10° tilt range, which makes it easy to angle a screen for sharing, standing use or glare control. Height Assist balances the...