Mounts & Racks

The Chief KSA1250B-2 lets you mount Dell monitors without tools. The bracket fits a Chief mount's 100 x 100 mm VESA interface with four screws, and from then on a Dell monitor simply clicks into place using the quick-release slots Dell builds into the back of its displays. There are no screws to line up while holding the screen, so first installs and later replacements take seconds. That helps IT teams rolling out or refreshing large fleets of Dell monitors. The bracket supports up to 25 lb...

The Chief KTA1000B is a grommet mount accessory for Chief's pole-mounted monitor arrays. It anchors the array pole through a hole in the work surface, either an existing cable grommet or a hole drilled for it, giving a clean, low-profile base without a clamp along the desk edge. Grommet mounting is often chosen for multi-screen desks because it can place the pole anywhere on the surface, not just at the edge, and leaves the desk perimeter clear. Chief lists it as a multi-display accessory for...

The Chief KTA1000S is a grommet mount accessory for Chief's pole-mounted monitor arrays. It anchors the array pole through a hole in the work surface, either an existing cable grommet or a hole drilled for it, giving a clean, low-profile base without a clamp along the desk edge. Grommet mounting is often chosen for multi-screen desks because it can place the pole anywhere on the surface, not just at the edge, and leaves the desk perimeter clear. Chief lists it as a multi-display accessory for...

The Chief KTA1001B is an array connector bracket from Chief's Array accessory family. Connector brackets join the components of a multi-display array, so integrators can build or extend a screen setup from standard Chief parts instead of buying a new array. That helps when a workstation goes from two screens to three, or when a layout has to change after users settle in. Keeping a few connectors in service stock also makes on-site changes quicker. The black finish matches black Chief array...

The Chief KTA1001S is an array connector bracket from Chief's Array accessory family. Connector brackets join the components of a multi-display array, so integrators can build or extend a screen setup from standard Chief parts instead of buying a new array. That helps when a workstation goes from two screens to three, or when a layout has to change after users settle in. Keeping a few connectors in service stock also makes on-site changes quicker. The silver finish matches silver Chief array...

The Chief KTA1002B is a freestanding base for Chief's pole-mounted monitor arrays. It sits on top of the work surface, so the array can be set up without clamping to the desk edge or drilling a grommet hole. That makes it a good choice for glass or stone desks, rented furniture, desks with no usable edge, and workstations that need to be moved or rearranged often. The base is fairly heavy for its size, with a shipping weight of about 16.4 lb, which helps it stay stable. The black finish...

The Chief KTA1002S is a freestanding base for Chief's pole-mounted monitor arrays. It sits on top of the work surface, so the array can be set up without clamping to the desk edge or drilling a grommet hole. That makes it a good choice for glass or stone desks, rented furniture, desks with no usable edge, and workstations that need to be moved or rearranged often. The base is fairly heavy for its size, with a shipping weight of about 16.4 lb, which helps it stay stable. The silver finish...

The Chief KTA1003B is a dual pole clamp from Chief's Array accessory family. In larger multi-display setups, two poles are sometimes used to spread the load or set up wider or taller screen layouts, and a dual pole clamp ties the parts of that setup together. Integrators use parts like this to build a custom array from standard Chief components instead of having special brackets made. The black finish matches black Chief array hardware for a clean, consistent look. Distributor data describes...

The Chief KTA1003S is a dual pole clamp from Chief's Array accessory family. In larger multi-display setups, two poles are sometimes used to spread the load or set up wider or taller screen layouts, and a dual pole clamp ties the parts of that setup together. Integrators use parts like this to build a custom array from standard Chief components instead of having special brackets made. The silver finish matches silver Chief array hardware for a clean, consistent look. Distributor data describes...

The Chief KTA1004B is a desk clamp for Chief's pole-mounted monitor arrays. It attaches the array pole to the edge of the work surface and handles desks from 0.5 to 3.25 in (13-82 mm) thick, which covers most office, benching, and heavy-duty console tops. Clamp mounting needs no holes, so it is a good fit for leased furniture or desks you may move later, and it is easy to reposition along the edge if the layout changes. Distributor data describes it as a desk clamp for pole arrays. The black...

The Chief KTA1004S is a desk clamp for Chief's pole-mounted monitor arrays. It attaches the array pole to the edge of the work surface and handles desks from 0.5 to 3.25 in (13-82 mm) thick, which covers most office, benching, and heavy-duty console tops. Clamp mounting needs no holes, so it is a good fit for leased furniture or desks you may move later, and it is easy to reposition along the edge if the layout changes. Distributor data describes it as a desk clamp for pole arrays. The silver...

The Chief KTA1005B is a Turn-Tite Centris head from the Kontour Array accessory range, finished in black. The head is the component that connects a display to the array and gives it tilt adjustment. Chief's Centris design places the pivot close to the display's centre of gravity, so the screen can be angled with light hand pressure and stays where it is set. Integrators use individual heads to add an extra screen position to a custom array, to replace a damaged part, or to keep spares for a...

The Chief KTA1005S is a Turn-Tite Centris head from the Kontour Array accessory range, finished in silver. The head is the component that connects a display to the array and gives it tilt adjustment. Chief's Centris design places the pivot close to the display's centre of gravity, so the screen can be angled with light hand pressure and stays where it is set. Integrators use individual heads to add an extra screen position to a custom array, to replace a damaged part, or to keep spares for a...

The Chief KTA1007B is a large grommet mount accessory for the Kontour Array system, finished in black. It secures an Array pole to the work surface through a grommet hole, so the mount takes up very little desk space and needs no clamp on the desk edge. Use it as the base of a custom array: pick a KTA pole in the height you need, add KTA pole clamps for two, three or more displays, and the grommet base ties the assembly to the desk. This route suits furniture where the edge of the desk is not...

The Chief KTA1007S is a large grommet mount accessory for the Kontour Array system, finished in silver. It secures an Array pole to the work surface through a grommet hole, so the mount takes up very little desk space and needs no clamp on the desk edge. Use it as the base of a custom array: pick a KTA pole in the height you need, add KTA pole clamps for two, three or more displays, and the grommet base ties the assembly to the desk. This route suits furniture where the edge of the desk is not...

The Chief KTA1014B is a 14-inch pole from the Kontour Array accessory family, finished in black. It is the vertical backbone of a custom multi-monitor array: you attach Chief KTA pole clamps to hold the displays, then anchor the pole to the work surface with a compatible Array base, such as the KTA1007 large grommet accessory. Poles are offered in several lengths, so you can choose the height that suits the number of rows and the size of the screens you plan to stack. Ordering by component...

The Chief KTA1014S is a 14-inch pole from the Kontour Array accessory family, finished in silver. It is the vertical backbone of a custom multi-monitor array: you attach Chief KTA pole clamps to hold the displays, then anchor the pole to the work surface with a compatible Array base, such as the KTA1007 large grommet accessory. Poles are offered in several lengths, so you can choose the height that suits the number of rows and the size of the screens you plan to stack. Ordering by component...

The Chief KTA1028B is a 28-inch pole from the Kontour Array accessory family, finished in black. It is the vertical backbone of a custom multi-monitor array: you attach Chief KTA pole clamps to hold the displays, then anchor the pole to the work surface with a compatible Array base, such as the KTA1007 large grommet accessory. Poles are offered in several lengths, so you can choose the height that suits the number of rows and the size of the screens you plan to stack. Ordering by component...

The Chief KTA1028S is a 28-inch pole from the Kontour Array accessory family, finished in silver. It is the vertical backbone of a custom multi-monitor array: you attach Chief KTA pole clamps to hold the displays, then anchor the pole to the work surface with a compatible Array base, such as the KTA1007 large grommet accessory. Poles are offered in several lengths, so you can choose the height that suits the number of rows and the size of the screens you plan to stack. Ordering by component...

The Chief KTA1036B is a 36-inch pole from the Kontour Array accessory family, finished in black. It is the vertical backbone of a custom multi-monitor array: you attach Chief KTA pole clamps to hold the displays, then anchor the pole to the work surface with a compatible Array base, such as the KTA1007 large grommet accessory. Poles are offered in several lengths, so you can choose the height that suits the number of rows and the size of the screens you plan to stack. Ordering by component...

The Chief KTA1036S is a 36-inch pole from the Kontour Array accessory family, finished in silver. It is the vertical backbone of a custom multi-monitor array: you attach Chief KTA pole clamps to hold the displays, then anchor the pole to the work surface with a compatible Array base, such as the KTA1007 large grommet accessory. Poles are offered in several lengths, so you can choose the height that suits the number of rows and the size of the screens you plan to stack. Ordering by component...

The Chief KTA1042B is a 42-inch pole from the Kontour Array accessory family, finished in black. It is the vertical backbone of a custom multi-monitor array: you attach Chief KTA pole clamps to hold the displays, then anchor the pole to the work surface with a compatible Array base, such as the KTA1007 large grommet accessory. Poles are offered in several lengths, so you can choose the height that suits the number of rows and the size of the screens you plan to stack. Ordering by component...

The Chief KTA1042S is a 42-inch pole from the Kontour Array accessory family, finished in silver. It is the vertical backbone of a custom multi-monitor array: you attach Chief KTA pole clamps to hold the displays, then anchor the pole to the work surface with a compatible Array base, such as the KTA1007 large grommet accessory. Poles are offered in several lengths, so you can choose the height that suits the number of rows and the size of the screens you plan to stack. Ordering by component...

The Chief KTA220B is a dual-monitor pole clamp from the Kontour Array accessory family. It clamps onto a Kontour Array pole and holds 2 displays in a single horizontal row, letting you build a multi-screen workstation from individual components rather than a fixed kit. Chief rates the clamp at 35 lbs (15.9 kg) and lists a typical screen size of 10"-22.7" (254mm - 577 mm). Displays can be set in landscape or portrait orientation. Add more clamps to the same pole to stack a second row, then...