Mounts & Racks

The Chief KRA226B is a center-of-table grommet plate for Kontour column-mounted monitor arms. In shared workstations where monitors face users on both sides of a table, the column mount needs a stable base that can handle arms extending in several directions. This plate provides that grommet mounting point and is required when building a four-arm K1C configuration using KRA221 expansion arm kits. It mounts through a grommet hole in the work surface for a clean installation with cables routed...

The Chief KRA226S is a center-of-table grommet plate for Kontour column-mounted monitor arms. In shared workstations where monitors face users on both sides of a table, the column mount needs a stable base that can handle arms extending in several directions. This plate provides that grommet mounting point and is required when building a four-arm K1C configuration using KRA221 expansion arm kits. It mounts through a grommet hole in the work surface for a clean installation with cables routed...

The Chief KRA227B is a dual monitor upgrade kit for Kontour K1 single-arm mounts, including the K1D desk, K1P pole, K1S slatwall and K1W wall versions. It adds a second fully articulating arm so the existing mount can carry two independent monitors, avoiding the need to replace the whole mount. Each arm supports monitors from 5 to 25 lb, reaches up to 21.6 inches and tilts 75 degrees up and 10 degrees down for comfortable viewing whether seated or standing. Monitors with VESA 75 x 75 or 100 x...

The Chief KRA227BXRH is the reduced-height version of the Kontour K1 dual monitor expansion kit. It adds a second articulating arm to an existing single-arm K1D, K1P, K1S or K1W reduced-height mount, converting, for example, a K1D120 into a K1D220-style dual-arm configuration. Each arm handles monitors of 5 to 25 lb, typically 10 to 32 inches. The reduced-height format keeps the arm assembly lower, which helps preserve sight lines in open offices and suits users who prefer screens closer to...

The Chief KRA227S is a dual monitor upgrade kit for Kontour K1 single-arm mounts, including the K1D desk, K1P pole, K1S slatwall and K1W wall versions. It adds a second fully articulating arm so the existing mount can carry two independent monitors, avoiding the need to replace the whole mount. Each arm supports monitors from 5 to 25 lb, reaches up to 21.6 inches and tilts 75 degrees up and 10 degrees down for comfortable viewing whether seated or standing. Monitors with VESA 75 x 75 or 100 x...

The Chief KRA227SXRH is the reduced-height version of the Kontour K1 dual monitor expansion kit. It adds a second articulating arm to an existing single-arm K1D, K1P, K1S or K1W reduced-height mount, converting, for example, a K1D120 into a K1D220-style dual-arm configuration. Each arm handles monitors of 5 to 25 lb, typically 10 to 32 inches. The reduced-height format keeps the arm assembly lower, which helps preserve sight lines in open offices and suits users who prefer screens closer to...

The Chief KRA228B is a dual monitor upgrade kit for Kontour K2 single-arm mounts in the pole (K2P) and wall (K2W) styles. It adds a second articulating arm so the existing mount can support two independently adjustable monitors. Each arm reaches up to 17.1 inches, tilts 15 degrees up or down, and accepts monitors up to 25 lb with VESA 75 x 75 or 100 x 100 mm patterns in landscape or portrait. Minimum depth is 2.95 inches. Upgrading the mount you already have is faster and less costly than...

The Chief KRA231B is a column-mounted extreme tilt head for Kontour K1C and K2C column mounts. Instead of using an articulating arm, it attaches a monitor straight to the column, giving a compact, fixed-reach position with a very wide tilt range. The head tilts 75 degrees up and 10 degrees down, making it useful for screens that need to lie back for touch input, document review or sharing across a counter. It supports monitors up to 25 lb with VESA 75 x 75 or 100 x 100 mm patterns, in...

The Chief KRA231S is a column-mounted extreme tilt head for Kontour K1C and K2C column mounts. Instead of using an articulating arm, it attaches a monitor straight to the column, giving a compact, fixed-reach position with a very wide tilt range. The head tilts 75 degrees up and 10 degrees down, making it useful for screens that need to lie back for touch input, document review or sharing across a counter. It supports monitors up to 25 lb with VESA 75 x 75 or 100 x 100 mm patterns, in...

The Chief KRA232B is a thin client PC mounting accessory that keeps small computers off the work surface by mounting them to Kontour K1C and K2C columns. It mounts to the column in several orientations and can alternatively be installed under the desktop when that location is preferred. Hook-and-loop straps hold the PC and its cables in place. It accepts thin client, zero client and similar small devices up to 8 x 8 x 1.7 inches, and provides VESA 75 x 75 and 100 x 100 mm hole patterns for...

The Chief KRA232PB is a thin client PC mounting accessory that keeps small computers off the work surface by mounting them to 1.9 in OD KTA, CMS and CPA poles. It clamps to standard 1.9 inch outside-diameter poles, including Chief KTA pole accessories and CPA and CMS poles. Hook-and-loop straps hold the PC and its cables in place. It accepts thin client, zero client and similar small devices up to 8 x 8 x 1.7 inches, and provides VESA 75 x 75 and 100 x 100 mm hole patterns for devices that...

The Chief KRA233B is a secure thin client PC mounting accessory that keeps small computers off the work surface by mounting them to Kontour K1C and K2C columns. It mounts to the column in several orientations and can alternatively be installed under the desktop when that location is preferred. Unlike the open-bracket version, this model fully encloses the device, discouraging tampering and theft in libraries, kiosks, reception areas and other public spaces. It accepts thin client, zero client...

The Chief KRA233PB is a secure thin client PC mounting accessory that keeps small computers off the work surface by mounting them to 1.9 in OD KTA, CMS and CPA poles. It clamps to standard 1.9 inch outside-diameter poles, including Chief KTA pole accessories and CPA and CMS poles. Unlike the open-bracket version, this model fully encloses the device, discouraging tampering and theft in libraries, kiosks, reception areas and other public spaces. It accepts thin client, zero client and similar...

The Chief KRA235B FleXlink Arm Kit is an extension accessory in the Kontour monitor mount family. It adds an extra link to a Kontour desk mount configuration, giving more reach and flexibility in where the monitor can be positioned. That is useful on deep work surfaces, at L-shaped desks, or when a screen must clear other equipment on the desk. Because it extends an existing arm rather than replacing it, the FleXlink kit lets installers adapt a workstation as needs change without starting...

The Chief KRA235S FleXlink Arm Kit is an extension accessory in the Kontour monitor mount family. It adds an extra link to a Kontour desk mount configuration, giving more reach and flexibility in where the monitor can be positioned. That is useful on deep work surfaces, at L-shaped desks, or when a screen must clear other equipment on the desk. Because it extends an existing arm rather than replacing it, the FleXlink kit lets installers adapt a workstation as needs change without starting...

The Chief KRA240B is a K1 dynamic arm kit that adds gas-spring height adjustment to Kontour K2 articulating arm mounts. K2 arms are positioned and then stay put; this kit swaps in a dynamic segment so users can raise or lower the monitor through 13 inches of travel with a light push. That makes it a good fit for sit-stand desks and shared workstations where screen height changes throughout the day. It supports monitors from 5 to 25 lb in most applications, includes a tool-free cable cover for...

The Chief KRA240S is a K1 dynamic arm kit that adds gas-spring height adjustment to Kontour K2 articulating arm mounts. K2 arms are positioned and then stay put; this kit swaps in a dynamic segment so users can raise or lower the monitor through 13 inches of travel with a light push. That makes it a good fit for sit-stand desks and shared workstations where screen height changes throughout the day. It supports monitors from 5 to 25 lb in most applications, includes a tool-free cable cover for...

The Chief KRA241B is a hardware kit for Kontour KX, K1 and K2 series monitor arms. It supplies mounting and installation hardware for these arms, making it a useful spare when workstations are moved, furniture is swapped, or original parts have gone missing after a reconfiguration. Keeping a few kits on hand helps facilities teams and installers finish jobs without waiting on replacement parts. The black finish matches the corresponding Kontour arms. This is a hardware-only item; it does not...

The Chief KRA241S is a hardware kit for Kontour KX, K1 and K2 series monitor arms. It supplies mounting and installation hardware for these arms, making it a useful spare when workstations are moved, furniture is swapped, or original parts have gone missing after a reconfiguration. Keeping a few kits on hand helps facilities teams and installers finish jobs without waiting on replacement parts. The silver finish matches the corresponding Kontour arms. This is a hardware-only item; it does not...

The Chief KRA243B is a monitor interface plate made for the Kontour K1 family of desk monitor arms. The interface plate is the bracket that connects the back of the display to the arm, so it is the part that carries the screen and lets you take it on and off the arm. Facility teams and integrators often keep a few on hand when they move displays between workstations, replace a damaged bracket, or standardize a fleet of K1 arms that came from different orders. This version has a black finish to...

The Chief KRA243S is a monitor interface plate made for the Kontour K1 family of desk monitor arms. The interface plate is the bracket that connects the back of the display to the arm, so it is the part that carries the screen and lets you take it on and off the arm. Facility teams and integrators often keep a few on hand when they move displays between workstations, replace a damaged bracket, or standardize a fleet of K1 arms that came from different orders. This version has a silver finish...

The Chief KRA244B is a desk clamp base for the Kontour K1D desk-mount monitor arm. It is a conversion accessory: it lets an existing K1D arm attach to the desk with a clamp, so a workstation can be reconfigured without buying a whole new arm. A clamp grips the edge of the work surface, which suits furniture you do not want to drill through, such as rented desks, benching systems, or desks that may move later. The black finish matches black Kontour arms for a uniform look across a deployment....

The Chief KRA244S is a desk clamp base for the Kontour K1D desk-mount monitor arm. It is a conversion accessory: it lets an existing K1D arm attach to the desk with a clamp, so a workstation can be reconfigured without buying a whole new arm. A clamp grips the edge of the work surface, which suits furniture you do not want to drill through, such as rented desks, benching systems, or desks that may move later. The silver finish matches silver Kontour arms for a uniform look across a deployment....

The Chief KRA245B is a desk clamp base for Kontour column-style monitor arms, the K1C and K2C models in the KXC family. The base clamps the column upright to the edge of the work surface, so the arms can be mounted without a grommet hole or drilling. It works for new installs and is also a straightforward way to change how an existing column arm attaches when furniture changes. Chief lists the part as an installation and mounting-bracket accessory for desk and tabletop use, and it is TAA...