Mounts & Racks

The Chief KITQS012C gathers everything needed to hang a projector from suspended (drop) ceilings under a single part number, so there is no need to source a mount, column and ceiling hardware separately. At its core is the RPMAU RPA Elite universal projector mount (black), a universal design rated for projectors up to 50 lbs. It offers independent roll, pitch and yaw adjustment, with micro-adjust controls for fine image alignment, letting the installer square the picture to the screen without...

The Chief KITS006P is a suspended-ceiling installation kit for projector projects where the mount is chosen separately. It combines the CMS440 lightweight suspended ceiling kit, which bridges the ceiling grid above the tile, the CMS006 6" (15.2 cm) fixed extension column, and the CMA470 plenum-rated above-tile storage accessory, giving a tidy place for power, cabling and small AV equipment above the ceiling. Because the components are supplied together under one part number, integrators can...

The Chief KITS006PW is a suspended-ceiling installation kit for projector projects where the mount is chosen separately. It combines the CMS440 lightweight suspended ceiling kit, which bridges the ceiling grid above the tile, the CMS006W 6" (15.2 cm) fixed extension column, and the CMA470 plenum-rated above-tile storage accessory, giving a tidy place for power, cabling and small AV equipment above the ceiling. Because the components are supplied together under one part number, integrators can...

The Chief KITXWXSM1U is a complete extra-large static wall mount kit from the Fusion family, designed for the long, shallow mounting patterns used on 21:9 ultrawide displays. It accepts VESA-style patterns from 1300 x 100 mm through 1954 x 600 mm and supports up to 250 lb, covering typical screen sizes from 80 to 120 inches. Because the mount holds the display just 2.25 inches from the wall, it suits corridors, boardrooms and public spaces where a flush look matters. Installers get room to...

The Chief KITXWXSM1UP is the portrait version of the Fusion ultrawide static wall mount kit. It is built for installations where a large ultrawide display needs to stand vertically, such as tall wayfinding or advertising signage. The kit supports up to 250 lb and typical screen sizes of 80 to 120 inches, accepting mounting patterns from 100 x 600 mm to 891 x 1500 mm. At just 2.25 inches deep, it keeps the display tight to the wall for a clean architectural look. Fusion conveniences carry over...

The Chief KMA220B is a dual horizontal array accessory for Chief K-series pivot and swing arm mounts. Rather than buying a new multi-monitor mount, you attach this bar to an existing K-series arm and hang 2 flat panel monitors next to each other. Each monitor has its own adjustment, and Centris TurnTite dials hold the position once it is set, so screens stay aligned through daily use. The array accepts monitors with VESA 75 x 75 mm or 100 x 100 mm patterns and supports 11 lb (5 kg) per screen....

The Chief KMA320B is a triple horizontal array accessory for Chief K-series pivot and swing arm mounts. Rather than buying a new multi-monitor mount, you attach this bar to an existing K-series arm and hang 3 flat panel monitors next to each other. Each monitor has its own adjustment, and Centris TurnTite dials hold the position once it is set, so screens stay aligned through daily use. The array accepts monitors with VESA 75 x 75 mm or 100 x 100 mm patterns and supports 10 lb (4.5 kg) per...

The Chief KPP110B is a compact pivot/tilt head that mounts a single display to a pole. It clamps onto poles from 1.75 to 2 inches in diameter, making it useful on desk poles, ceiling or floor columns and existing pole-based workstations. The mount supports up to 40 lb and offers swivel and tilt so the screen can be angled toward the user, plus roll adjustment after installation to get the display perfectly level. Screens can be hung in either landscape or portrait orientation. With a minimum...

The Chief KPP110S is a compact pivot/tilt head that mounts a single display to a pole. It clamps onto poles from 1.75 to 2 inches in diameter, making it useful on desk poles, ceiling or floor columns and existing pole-based workstations. The mount supports up to 40 lb and offers swivel and tilt so the screen can be angled toward the user, plus roll adjustment after installation to get the display perfectly level. Screens can be hung in either landscape or portrait orientation. With a minimum...

The Chief KRA219B is a narrow-gap table clamp kit for Kontour K1 and K2 desk-mounted monitor arms. Standard clamps need room behind the desk edge, which is not always available when a work surface sits close to a wall, cubicle panel or another desk. This kit gives installers a clamp option for those tight spots so the arm can still be fixed securely to the desktop. It is rated for 40 lb, is TAA compliant for government and education purchasing, and comes in a black finish that matches the rest...

The Chief KRA219S is a narrow-gap table clamp kit for Kontour K1 and K2 desk-mounted monitor arms. Standard clamps need room behind the desk edge, which is not always available when a work surface sits close to a wall, cubicle panel or another desk. This kit gives installers a clamp option for those tight spots so the arm can still be fixed securely to the desktop. It is rated for 40 lb, is TAA compliant for government and education purchasing, and comes in a silver finish that matches the...

The Chief KRA220B is an extension arm accessory for Kontour K1 and K2 monitor mounts. It adds up to 6.5 inches of reach between the mount and the display, which helps on deep desks, at workstations against a wall, or anywhere a user needs the screen pulled further forward. Because a longer lever arm puts more load on the mount, using this extension reduces the host arm's weight capacity by 15 lb, so confirm the monitor still falls within the adjusted rating. The black finish matches the rest...

The Chief KRA220S is an extension arm accessory for Kontour K1 and K2 monitor mounts. It adds up to 6.5 inches of reach between the mount and the display, which helps on deep desks, at workstations against a wall, or anywhere a user needs the screen pulled further forward. Because a longer lever arm puts more load on the mount, using this extension reduces the host arm's weight capacity by 15 lb, so confirm the monitor still falls within the adjusted rating. The silver finish matches the rest...

The Chief KRA221B is an expansion arm kit for Kontour K1C column-mounted monitor arms. It lets you add another arm to a K1C installation that is already in place, the most common use being turning a single-arm K1C120 into a dual-arm K1C220. Additional kits can be used to build out a third or fourth arm for shared center-of-table workstations; four-arm configurations require the KRA226 center-of-table grommet plate. Each arm supports monitors from 5 to 22 lb. Expanding an existing column is...

The Chief KRA221BXRH is an expansion arm kit for Kontour K1C column-mounted monitor arms in the reduced-height (XRH) format. It lets you add another arm to a K1C installation that is already in place, the most common use being turning a single-arm K1C120 into a dual-arm K1C220. Additional kits can be used to build out a third or fourth arm for shared center-of-table workstations; four-arm configurations require the KRA226 center-of-table grommet plate. Each arm supports monitors from 5 to 22...

The Chief KRA221S is an expansion arm kit for Kontour K1C column-mounted monitor arms. It lets you add another arm to a K1C installation that is already in place, the most common use being turning a single-arm K1C120 into a dual-arm K1C220. Additional kits can be used to build out a third or fourth arm for shared center-of-table workstations; four-arm configurations require the KRA226 center-of-table grommet plate. Each arm supports monitors from 5 to 22 lb. Expanding an existing column is...

The Chief KRA221SXRH is an expansion arm kit for Kontour K1C column-mounted monitor arms in the reduced-height (XRH) format. It lets you add another arm to a K1C installation that is already in place, the most common use being turning a single-arm K1C120 into a dual-arm K1C220. Additional kits can be used to build out a third or fourth arm for shared center-of-table workstations; four-arm configurations require the KRA226 center-of-table grommet plate. Each arm supports monitors from 5 to 22...

The Chief KRA222B is an expansion arm kit for the Kontour K2C column-mounted monitor arm. When a user who started on a single-arm K2C120 needs a second screen, this kit adds another arm to the existing column so both monitors are supported from one desk mount. That saves the cost and downtime of pulling the original mount and installing a new dual model. The black finish matches the rest of the K2C line, so the upgraded mount looks like it was ordered that way from the start. Weight capacity...

The Chief KRA222S is an expansion arm kit for the Kontour K2C column-mounted monitor arm. When a user who started on a single-arm K2C120 needs a second screen, this kit adds another arm to the existing column so both monitors are supported from one desk mount. That saves the cost and downtime of pulling the original mount and installing a new dual model. The silver finish matches the rest of the K2C line, so the upgraded mount looks like it was ordered that way from the start. Weight capacity...

The Chief KRA223B is a dual monitor array accessory for Kontour K1 and K2 monitor arms. Mounted to an existing single arm, it creates a 2x1 side-by-side layout so two monitors move together as one unit. That keeps both screens aligned when the user repositions the arm, which is handy at sit-stand desks and shared stations. Capacity depends on the host arm: on K1 mounts each monitor can weigh 2 to 9 lb, while on K2 mounts each can be up to 15 lb. Add the KRA224 array handle for an easy grip...

The Chief KRA223S is a dual monitor array accessory for Kontour K1 and K2 monitor arms. Mounted to an existing single arm, it creates a 2x1 side-by-side layout so two monitors move together as one unit. That keeps both screens aligned when the user repositions the arm, which is handy at sit-stand desks and shared stations. Capacity depends on the host arm: on K1 mounts each monitor can weigh 2 to 9 lb, while on K2 mounts each can be up to 15 lb. Add the KRA224 array handle for an easy grip...

The Chief KRA224B is a handle accessory designed to work with the Kontour KRA223 dual monitor array. Together, the two accessories upgrade an existing K1 or K2 single-arm monitor mount into a dual-monitor array with a handle, matching the configuration of Chief's factory dual-array models. The handle gives users a natural grip point for adjusting height, reach and angle of both screens at once, rather than pushing on the monitor bezels. This is especially useful at sit-stand desks and shared...

The Chief KRA225B is a replacement monitor head that brings the Centris Extreme Tilt feature set to enhanced Kontour K2 series articulating arms. Out of the box, K2 arms use a simpler head; this accessory swaps in the more capable assembly used on Kontour K1 mounts. It provides 75 degrees of upward tilt and 10 degrees down, so the screen can be angled comfortably for seated or standing work, or tipped far back for shared viewing and touch use. A quick-release interface lets the monitor be...

The Chief KRA225S is a replacement monitor head that brings the Centris Extreme Tilt feature set to enhanced Kontour K2 series articulating arms. Out of the box, K2 arms use a simpler head; this accessory swaps in the more capable assembly used on Kontour K1 mounts. It provides 75 degrees of upward tilt and 10 degrees down, so the screen can be angled comfortably for seated or standing work, or tipped far back for shared viewing and touch use. A quick-release interface lets the monitor be...