Mounts & Racks

The Chief FCA813 is a minimal, low-profile shelf for adding a small USB webcam to a Fusion-mounted extra-large display. Instead of the wider component shelves in the Fusion range, it uses a 1.5-inch platform that keeps the hardware visually out of the way while placing the camera right at the edge of the screen, where eye contact on video calls looks most natural. The arm adjusts in height through a 18.0"-30.8" (457-782 mm) range from the center of the display, so it can clear the top or...

The Chief FCA815 adds a 8-inch equipment shelf to a Fusion Series display installation. It attaches to the Fusion mount interface and can be set either above the screen, where it makes a natural home for a video-conferencing camera, or below it for a small media player, codec or wireless presentation receiver. A turned-up lip on the end of the shelf helps keep gear in place, and the bracket keeps the installation tidy without a separate wall shelf or extra holes in the drywall. Because it uses...

Dual-display conference rooms often end up with the camera stuck above one screen, which leaves remote participants looking off to the side. The Chief FCA820 solves that by placing the camera on a 8-inch shelf in the center seam between two side-by-side flat panels, so the lens sits on the room's true centerline. The shelf is designed so the two displays can still be pushed together with only about a 1-inch (25 mm) gap. On a wall, it pairs with two Fusion fixed or tilt wall mounts joined by...

Dual-display conference rooms often end up with the camera stuck above one screen, which leaves remote participants looking off to the side. The Chief FCA821 solves that by placing the camera on a 14-inch shelf in the center seam between two side-by-side flat panels, so the lens sits on the room's true centerline. The shelf is designed so the two displays can still be pushed together with only about a 1-inch (25 mm) gap. On a wall, it pairs with two Fusion fixed or tilt wall mounts joined by...

The Chief FCA830 lets a center-channel speaker or soundbar travel with the display instead of needing its own wall bracket. It attaches to a Chief Fusion mount and suspends the speaker centered beneath a 53"-80" screen, keeping dialogue and far-end audio anchored to the picture. Its universal design accommodates most speaker brands. Chief lists an extension range of 13" - 20" (33.02 - 50.80 cm) for positioning the speaker relative to the screen. The adapter has a low profile, so it does not...

The Chief FCA831 attaches to a Chief Fusion display mount and extends out to each side of the screen so a pair of stereo speakers can hang flanking a 42"-70" display. Because the speakers ride on the display mount, the whole system installs as one unit and stays aligned with the picture, with no extra wall brackets to locate. The adapter spans an adjustable width that depends on the Fusion mount it is paired with: large Fusion wall mounts 36.8"-66.8" (934.7-1696.7 mm); medium Fusion wall...

The Chief FCA832 lets a center-channel speaker or soundbar travel with the display instead of needing its own wall bracket. It attaches to a Chief Fusion mount and suspends the speaker centered beneath a 53"-80" screen, keeping dialogue and far-end audio anchored to the picture. Its universal arms adjust in width from 5.5 to 21 inches, so it can grip a wide range of speaker and soundbar sizes. The adapter has a low profile, so it does not push the display farther from the wall, and Chief lists...

The Chief FCA840 lets a center-channel speaker or soundbar travel with the display instead of needing its own wall bracket. It attaches to a Chief Fusion mount and suspends the speaker centered beneath a 70"-100" screen, keeping dialogue and far-end audio anchored to the picture. Its universal design accommodates most speaker brands. Chief lists an extension range of 18" - 31" (45.72 - 78.74 cm) for positioning the speaker relative to the screen. The adapter has a low profile, so it does not...

The Chief FCA841 attaches to a Chief Fusion display mount and extends out to each side of the screen so a pair of stereo speakers can hang flanking a 50"-95" display. Because the speakers ride on the display mount, the whole system installs as one unit and stays aligned with the picture, with no extra wall brackets to locate. The adapter spans an adjustable width that depends on the Fusion mount it is paired with: Fusion wall mounts 44.8"-84.8" (1137.9-2153.9 mm); Fusion ceiling/cart...

The Chief FCA842 lets a center-channel speaker or soundbar travel with the display instead of needing its own wall bracket. It attaches to a Chief Fusion mount and suspends the speaker centered beneath a 70"-100" screen, keeping dialogue and far-end audio anchored to the picture. Its universal arms adjust in width from 5.5 to 21 inches, so it can grip a wide range of speaker and soundbar sizes. Chief lists an extension range of 18" - 31" (45.72 - 78.74 cm) for positioning the speaker relative...

The Chief FCA850 gives system designers a way to put the conferencing camera off to one side of the display instead of directly above or below it. That is useful when a room's seating, a wide video wall or a ceiling-height limit makes a centered camera impractical, or when the camera should match a presenter position. The 5.6-inch shelf adjusts in extension, height, lateral position and tilt, so the camera can be aimed precisely at the table after the display is hung. It carries up to 5 lbs....

The Chief FCA870 is a stackable shelf that expands the component storage on a Fusion flat panel installation. Rather than mounting on its own, it hangs below an FCA8XX series below-display shelf or center speaker accessory, giving you a second level for a codec, streaming player, small switcher or similar device. Chief lists equipment height clearance of about 7.3 to 10.3 inches when stacked under a center speaker mount and 10.1 to 13.1 inches between shelves. The shelf carries up to 10 lbs...

The Chief FCAB3X1U is the back-row add-on for a Fusion large ceiling-mounted 3x1 menu board. Added to an existing front-facing 3x1 system, it carries a second row of three landscape displays so the board can be read from both sides, which is how Chief arrives at its six-display rating for the completed back-to-back array. Chief lists typical screen sizes of 40 to 55 inches, extending to 65 inches when FCAX extension brackets are used, and a tilt range of +5 to -20 degrees for aiming the...

The Chief FCAB3X1UP is an add-on accessory for the Fusion large ceiling multi-display system. It adds a second, rear-facing row of three portrait-orientation displays to a 3x1 Fusion ceiling configuration, creating a back-to-back arrangement that can be read from both sides of a counter or concourse. Each position accepts displays in the 40-55 in class, and 65 in screens can be accommodated with Chief FCAX extension brackets. Universal interface hardware handles VESA patterns of any width by...

The Chief FCABX18 is a height extension accessory for Fusion LBM multi-display configurations. It adds 18 in (45.7 cm) of extension to the support columns, raising or lowering the display array so it sits at the right sightline for the space. Rather than re-engineering the structure, installers can use these extensions to adapt a standard Fusion layout to taller ceilings or to lift content above counters, crowds or obstructions. The extension ships in black to match the rest of the Fusion...

The Chief FCABX36 extends the column uprights of a Fusion LBM bolt-down freestanding video wall by 36 inches. Use it when the standard column height leaves the bottom row of displays too low, for example in lobbies where the wall must clear reception furniture or in public spaces where viewers stand at a distance. It is finished in black to match Fusion hardware, is UL Listed and TAA compliant, and ships in a 40.5 x 6.25 x 6.25 inch carton weighing 10.25 lbs. Chief publishes no further written...

The Chief FCAC is a connector for installations that hang several Fusion LCM ceiling menu boards side by side. It spans the gap between the extrusions of two neighboring menu boards, up to 12 inches apart, holding them in line so the row of screens reads as one continuous board. Chief is clear that the FCAC is an alignment and appearance aid only: it does not carry weight, and each menu board must still be fully supported by its own ceiling hardware. Connectors do not join to one another, so...

The Chief FCAC06B side cover closes off the open sides of a wall-mounted display or video wall, hiding the mount, cables and wall gap for a finished, built-in look. Each package includes two covers in 84-inch lengths with a 6-inch depth, and the material can be trimmed on site to the exact length, tilt or depth an installation needs using the hand or power tools installers already carry. A living hinge lets the cover swing open for service while remaining tamper-resistant in public spaces, and...

The Chief FCAC1LB is a back cover for single display Fusion installations where the rear of the screens is on view, such as ceiling-hung signage, mobile carts and freestanding video walls. A lightweight, adjustable steel frame attaches to the Fusion extrusion with a locking interface, and a black polyester diamond knit fabric stretches tightly over it to hide the mount, cables and hardware. Each end of the frame curves toward the display so the edges look finished from the side. Chief lists...

The Chief FCAC1XB is a back cover for single display Fusion installations where the rear of the screens is on view, such as ceiling-hung signage, mobile carts and freestanding video walls. A lightweight, adjustable steel frame attaches to the Fusion extrusion with a locking interface, and a black polyester diamond knit fabric stretches tightly over it to hide the mount, cables and hardware. Each end of the frame curves toward the display so the edges look finished from the side. The fabric has...

The Chief FCAC2X1LB is a back cover for two-display (2x1) Fusion installations where the rear of the screens is on view, such as ceiling-hung signage, mobile carts and freestanding video walls. A lightweight, adjustable steel frame attaches to the Fusion extrusion with a locking interface, and a black polyester diamond knit fabric stretches tightly over it to hide the mount, cables and hardware. Each end of the frame curves toward the display so the edges look finished from the side. Chief...

The Chief FCAC2X1MB is a back cover for two-display (2x1) Fusion installations where the rear of the screens is on view, such as ceiling-hung signage, mobile carts and freestanding video walls. A lightweight, adjustable steel frame attaches to the Fusion extrusion with a locking interface, and a black polyester diamond knit fabric stretches tightly over it to hide the mount, cables and hardware. Each end of the frame curves toward the display so the edges look finished from the side. Chief...

The Chief FCAC3X1LB is a back cover for three-display (3x1) Fusion installations where the rear of the screens is on view, such as ceiling-hung signage, mobile carts and freestanding video walls. A lightweight, adjustable steel frame attaches to the Fusion extrusion with a locking interface, and a black polyester diamond knit fabric stretches tightly over it to hide the mount, cables and hardware. Each end of the frame curves toward the display so the edges look finished from the side. Chief...

The Chief FCAC3X1MB is a back cover for three-display (3x1) Fusion installations where the rear of the screens is on view, such as ceiling-hung signage, mobile carts and freestanding video walls. A lightweight, adjustable steel frame attaches to the Fusion extrusion with a locking interface, and a black polyester diamond knit fabric stretches tightly over it to hide the mount, cables and hardware. Each end of the frame curves toward the display so the edges look finished from the side. Chief...