Mounts & Racks

The Chief FPIWMKIT1 is the rough-in stage of the Tempo flat panel in-wall mount system. It lets the contractor set the in-wall boxes and stud tabs while the wall framing is still open, so the display mount itself can be delivered and installed after the drywall is finished. The boxes fit between 16-inch on-center studs and install much like standard in-wall boxes. Because they can be spaced as needed, the finished system adapts to a wide range of horizontal mounting patterns. Each box provides...

The Chief FPIWMKIT2 is the install-and-commission half of the Tempo flat panel in-wall mount system. It is delivered after the wall is finished and fits into the in-wall boxes set during rough-in with the FPIWMKIT1 kit. The kit supplies the trim flanges, in-wall rail assemblies, display interfaces and two 15 x 10 inch Lever Lock plates that provide at least 1 RU of clearance for small devices behind the screen. Devices can be shifted laterally inside the boxes, and the plates accept Middle...

The Chief FPIWMS Tempo flat panel in-wall mount system recesses large displays into the wall and hides small AV devices behind them. It ships as one package containing both stages of the install: the FPIWMKIT1 in-wall boxes and stud tabs that go in during rough-in, and the FPIWMKIT2 flanges, display mount and storage plates that go in after the drywall is finished. The boxes fit between 16-inch on-center wood or steel studs, and when installed per Chief instructions the system can eliminate...

The Chief FPIWSBX adds more hidden equipment space to a Tempo in-wall installation. Each 14 x 23 inch box fits between 16-inch on-center studs and installs like a standard in-wall box, so you can add as many as a project needs for media players, codecs, network switches or other small devices. A single 15 x 10 inch Lever Lock plate is supplied with each box, providing at least 1 RU of clearance and holding up to 20 lbs. Devices can be shifted laterally within the box, and the Lever Lock plate...

The Chief FRA Freestyle rotation adapter lets installers set displays at angles other than straight landscape or portrait, opening up artistic video wall layouts for retail, lobbies and venues. The adapter sits between the display and a Chief ConnexSys or Fusion mount and provides 90 degrees of rotation for a total range of 360 degrees, with positive lockouts every 15 degrees so screens land on repeatable angles. On ConnexSys, optional micro-adjustment helps fine-tune alignment, and displays...

The Chief FSB018BLK is a compact table stand for a single small flat panel or touchscreen. Its low-profile base takes up little counter or desk space, while adjustable friction holds the screen steady at any angle between 0 and 90 degrees, so it works for upright viewing, a laid-back touch position, or angled for privacy so neighbors cannot read the display. The height can be adjusted by 3.25 inches (82.6 mm), with an equipment height range of 8 to 16 inches, letting it suit different screen...

The Chief FSB1U is a universal interface bracket that sits between a small display and a Chief small flat panel or monitor mount. It accommodates displays with 75 x 75, 100 x 100 or 200 x 100 mm VESA hole patterns, and Chief's description also lists 200 x 200 mm support when used with Chief small flat panel mounting solutions. The bracket is designed to work with the Q-Latch mounting system used on the FSR fixed and FTR tilt wall mounts, letting the display hook on and latch quickly. Mounting...

The Chief FSB4073 is an interface bracket for small form-factor displays that use a 50 x 50 mm VESA mounting pattern, a size common on compact signage screens but not supported directly by most monitor mounts. The bracket bolts to the 50 mm pattern on the display and presents a 100 x 100 mm pattern, so the screen can be hung on a wide range of Chief monitor arms and small flat panel wall, ceiling or desk mounts. Chief notes that when used on Kontour K1-series height-adjustable monitor arms,...

The Chief FSB4090B is a custom interface bracket built for the Cisco EX90 desktop video conferencing system, which does not mount directly to a standard monitor arm. The bracket attaches to the EX90 and presents a 100 x 100 mm VESA threaded stud pattern on the back that connects to Chief Kontour K2-series arms and desk mounts, freeing desk space and allowing the screen and camera to be positioned for comfortable calls. An optional shelf is included to hold the telephone and touch panel that...

The Chief FSB4243B belongs to Chief's FSB family of custom interface brackets, which allow screens that lack a standard VESA hole pattern to be installed on Chief small flat panel mounting solutions. Each FSB bracket is matched to particular displays, bridging the display's own mounting points to the mount's interface so the screen hangs securely and level. The FSB4243B is compatible with Chief F-series and K-series mounts, including Kontour monitor arms and Chief small flat panel wall,...

The Chief FSB4245B is a custom interface bracket in Chief's FSB family, made to let a screen without a standard VESA hole pattern install on Chief small flat panel mounting solutions. FSB brackets are matched to particular displays and connect the display's own mounting points to the interface of the mount, so the screen hangs securely and level. Chief lists the FSB4245B as compatible with its F-series and K-series mounts, which include Kontour monitor arms and Chief small flat panel wall,...

The Chief FSB4442B is an interface bracket designed to mount the Samsung SH37F stretched display, a wide, short bar-type screen often used for shelf-edge retail, transit information and wayfinding. Because the display's height is limited, the bracket centers a 400 x 200 mm M8 attachment on the screen and lets it connect to compatible Chief mounts with a 100 x 100 mm interface. Chief notes that the mount used must fit within the display's footprint and that the overall interface height must...

The Chief FSB75100B is a kit of interface buttons and hardware used to attach a small flat panel monitor to Chief's FSR fixed or FTR tilt wall mounts. The buttons fasten to the back of the display so it can hang on the mount. The distributor describes it as a VESA 75/100 adapter, matching the 75 and 100 mm patterns common on small displays. It is useful as a replacement set when relocating displays, when hardware has been lost, or when equipping additional screens to hang on existing FSR or...

The Chief FSR100 is a compact fixed wall mount for small flat panel displays, sized for screens from 10 to 32 inches. It holds the display just 0.75 inches (1.9 cm) from the wall, giving a clean, close-to-the-wall look for signage and informational screens. The mount accepts displays with 50 x 50 mm or 100 x 100 mm VESA patterns, covering many small monitors, touch panels and signage screens. It mounts in landscape orientation and is finished in black. The FSR100 is the 100 mm version of...

The Chief FSR1U is the universal version of Chief's FSR small flat panel fixed wall mount. It supports a broad range of VESA patterns, from 50 x 50 mm through 75 x 75, 100 x 100, 200 x 100 and 200 x 200 mm, so one mount can cover most small monitors, touch panels and signage displays from 10 to 40 inches. It is rated for displays up to 45 lbs (20.4 kg) and installs to a single wall stud, making placement simple in corridors, beside doors or on narrow wall sections. With a minimum depth of just...

The Chief FTR100 is a small flat panel tilt wall mount built for digital signage and hospitality installs, where fast installation, easy adjustment and security in public spaces matter. Patented Centris technology lets the display be tilted with fingertip pressure and hold its angle, so screens can be angled toward viewers to cut glare. Chief's Q-Latch mounting system speeds installation by letting the display hang on the mount and latch in place. This 100 mm version accepts displays with 50 x...

The Chief FTR1U is a small flat panel tilt wall mount built for digital signage and hospitality installs, where fast installation, easy adjustment and security in public spaces matter. Patented Centris technology lets the display be tilted with fingertip pressure and hold its angle, so screens can be angled toward viewers to cut glare. Chief's Q-Latch mounting system speeds installation by letting the display hang on the mount and latch in place. As the universal version, it accepts VESA 50 x...

The Chief FWDSK110B is a dual swing arm wall mount for small flat panels, designed specifically to attach to a single steel stud, which makes it practical in commercial buildings with metal framing. The arm extends up to 15.85 inches (40.3 cm) so the screen can be pulled out and angled toward the viewer, then folded back to a depth of 2.85 inches when not in use. Centris technology provides smooth fingertip tilt through +/-15 degrees, pivot tension can be adjusted at each joint independently,...

The Chief HB010R is a custom interface bracket for Chief's VCM projector mounts. Rather than relying on an adjustable universal adapter, custom VCM interface brackets are made for one specific projector model, lining up with its mounting points so installation is quick and the projector hangs securely and centered. The matching custom hardware is included, which removes the guesswork of matching screws and spacers to the projector's own mounting points on site. The distributor identifies this...

The Chief HB011E is a custom interface bracket for Chief's VCM projector mounts. Rather than relying on an adjustable universal adapter, custom VCM interface brackets are made for one specific projector model, lining up with its mounting points so installation is quick and the projector hangs securely and centered. The matching custom hardware is included, which removes the guesswork of matching screws and spacers to the projector's own mounting points on site. Chief's listing does not name...

The Chief HB012R is a Custom VCM Interface Bracket, a projector-specific adapter used with Chief's VCM custom projector mounts. Rather than relying on adjustable universal arms, a custom interface bracket is built around the mounting-hole pattern of one particular projector, so the projector bolts to the bracket and the bracket connects to the VCM mount. The result is a tidy, purpose-matched connection that keeps the projector aligned and simplifies installation on jobs where that exact model...

The Chief HB014R is a Custom VCM Interface Bracket, a projector-specific adapter used with Chief's VCM custom projector mounts. Rather than relying on adjustable universal arms, a custom interface bracket is built around the mounting-hole pattern of one particular projector, so the projector bolts to the bracket and the bracket connects to the VCM mount. The result is a tidy, purpose-matched connection that keeps the projector aligned and simplifies installation on jobs where that exact model...

The Chief HB016E is a Custom VCM Interface Bracket, a projector-specific adapter used with Chief's VCM custom projector mounts. Rather than relying on adjustable universal arms, a custom interface bracket is built around the mounting-hole pattern of one particular projector, so the projector bolts to the bracket and the bracket connects to the VCM mount. The result is a tidy, purpose-matched connection that keeps the projector aligned and simplifies installation on jobs where that exact model...

The Chief HB018E is a Custom VCM Interface Bracket, a projector-specific adapter used with Chief's VCM custom projector mounts. Rather than relying on adjustable universal arms, a custom interface bracket is built around the mounting-hole pattern of one particular projector, so the projector bolts to the bracket and the bracket connects to the VCM mount. The result is a tidy, purpose-matched connection that keeps the projector aligned and simplifies installation on jobs where that exact model...