Mounts & Racks

The Chief WM240S is the extra-large arm in Chief's dual-stud short throw wall mount line, designed for projectors that must be positioned far out from the wall. The telescoping arm reaches up to 66 in and anchors across two studs, with 10 in of lateral shift to center the projector on the screen. A quick-connect system speeds installation, and integrated micro height and leveling adjustment simplifies final alignment. Cables stay hidden inside the arm's management channel, and All-Points...

The Chief WMA1S is a heavy duty wall mount accessory for situations where a projector or flat panel cannot be hung from the ceiling. It attaches to a single wood stud or a concrete wall and provides the anchor point for a Chief CMS extension column, which then carries your projector mount or display mount out from the wall. Extension is adjustable from 11.5 in to 19 in, and micro-adjustment with a height assist feature helps you fine-tune position during installation. Load ratings depend on...

The Chief WMA2S is a heavy duty wall mount accessory built for dual stud or concrete walls when ceiling mounting is not an option. It spans two studs and serves as the anchor for a Chief CMS extension column, which in turn supports your projector or flat panel mount. Built-in lateral shift lets you center the column between studs, and extension adjusts from 13 in to 21 in. Micro-adjustment with a height assist feature makes positioning easier during installation. Ratings depend on the wall: up...

The Chief WMAC16 is a cover accessory that tidies up the wall area behind a Chief WM-series short throw projector mount. Installers often place outlets, small amplifiers, switchers or surplus cable near the base of a projector arm, and this 16 in cover conceals them behind a clean silver panel. It installs without changing the lateral shift range or the stud alignment of the wall mount, so you can add it during the original install or later as a finishing upgrade. The cover measures 20 in...

The Chief WMAL24 is a 24 in lateral shift accessory that mounts between the wall and a Chief WM-series short throw arm or WMA2S heavy duty wall accessory. It solves two common problems: walls framed with studs 24 in on center, and installations where the projector must sit farther to one side than the mount's built-in shift allows. The plate spans the studs and gives up to 24 in of side-to-side adjustment, so you can center the projector on the screen without moving framing or adding blocking....

The Chief WP21S is a 24 in short throw projector wall arm from Chief's WP series, designed for mounting to wood studs, steel studs, concrete, block or brick. The projector mount slides along the arm for practically unlimited placement within the 2.38 - 23.78 in (6.05 - 60.40 cm) extension range, and integrated micro leveling plus 1.75 in of lateral shift help you dial in alignment after installation. Aesthetic covers and an inlay-style cable channel conceal wiring for a clean finish, and a 1.5...

The Chief WP21US is a 24 in short throw projector wall mount kit from Chief's WP series, designed for mounting to wood studs, steel studs, concrete, block or brick. It pairs the WP arm with the RSAUS RPA Mini universal projector mount, so the complete solution ships in one order. The projector mount slides along the arm for practically unlimited placement within the 2.38 - 23.78 in (6.05 - 60.40 cm) extension range, and integrated micro leveling plus 1.75 in of lateral shift help you dial in...

The Chief WP22S is a 40 in short throw projector wall arm from Chief's WP series, designed for mounting to wood studs, steel studs, concrete, block or brick. The projector mount slides along the arm for practically unlimited placement within the 2.38 - 39.12 in (6.05 - 99.36 cm) extension range, and integrated micro leveling plus 1.75 in of lateral shift help you dial in alignment after installation. Aesthetic covers and an inlay-style cable channel conceal wiring for a clean finish, and a 1.5...

The Chief WP22US is a 40 in short throw projector wall mount kit from Chief's WP series, designed for mounting to wood studs, steel studs, concrete, block or brick. It pairs the WP arm with the RSAUS RPA Mini universal projector mount, so the complete solution ships in one order. The projector mount slides along the arm for practically unlimited placement within the 2.38 - 39.12 in (6.05 - 99.36 cm) extension range, and integrated micro leveling plus 1.75 in of lateral shift help you dial in...

The Chief WP23S is a 56 in short throw projector wall arm from Chief's WP series, designed for mounting to wood studs, steel studs, concrete, block or brick. The projector mount slides along the arm for practically unlimited placement within the 2.38 - 55.12 in (6.05 - 140.00 cm) extension range, and integrated micro leveling plus 1.75 in of lateral shift help you dial in alignment after installation. Aesthetic covers and an inlay-style cable channel conceal wiring for a clean finish, and a...

The Chief WP23US is a 56 in short throw projector wall mount kit from Chief's WP series, designed for mounting to wood studs, steel studs, concrete, block or brick. It pairs the WP arm with the RSAUS RPA Mini universal projector mount, so the complete solution ships in one order. The projector mount slides along the arm for practically unlimited placement within the 2.38 - 55.12 in (6.05 - 140.00 cm) extension range, and integrated micro leveling plus 1.75 in of lateral shift help you dial in...

The Chief XBM1U is a Fusion freestanding bolt-down mount that lets you place a large display in the middle of a room, lobby or retail floor where no wall is available. It is configured for a single screen in landscape orientation and supports displays typically 55 in to 100 in and up to 250 lbs. Because the base bolts to the floor, it is intended as a permanent installation with a stable, secure footprint. Independent micro-adjustment for height and plumb, each up to 0.75 in, along with...

The Chief XBM1UP is the portrait-orientation version of Chief's Fusion extra-large freestanding bolt-down mount. It holds a single display, typically 55 in to 100 in and up to 250 lbs, upright for kiosk-style signage, menu boards and wayfinding. The base bolts to the floor for a permanent, secure installation in open areas with no wall to mount against. Height and plumb each micro-adjust up to 0.75 in, and lateral shift adds side-to-side fine tuning so the screen lines up cleanly. Integrated...

The Chief XCB1U is a Fusion extra-large ceiling mount that suspends two displays back to back from a single pole, so viewers on both sides of a space see a screen. It is built for landscape displays with VESA patterns from 200 x 100 mm to 800 x 400 mm and carries up to 200 lbs combined. The display interface is included, which keeps ordering simple. Each screen can tilt +/-5 degrees, with up to -20 degrees available on screens up to 38.8 in tall, so content can be angled down toward the...

The Chief XCB7000 is a Fusion extra-large ceiling mount that hangs two landscape displays back to back from a dual-column structure. The two-column design increases stability and capacity, supporting up to 300 lbs for larger or heavier screens than a single-pole mount can handle. It accepts VESA patterns from 200 x 100 mm to 800 x 400 mm, and offers height adjustment and tilt to set viewing angles, along with post-installation roll for final leveling. Because the display interface is not...

The Chief XCM1U is a Fusion ceiling mount that drops a single extra-large flat panel from one pole, a common choice for digital signage. It suits displays 5 in deep or thinner and supports up to 250 lbs, with VESA patterns from 200 x 100 mm to 800 x 400 mm. Tilt ranges from +5 to -20 degrees for aiming content down toward viewers, and post-installation roll adjustment lets you level the screen after it is hung. The mount adapts to traditional 1.5 in NPT columns and to Chief's CPA pinned...

The Chief XCM7000 is a Fusion dual-pole ceiling mount for extra-large displays that are too heavy or too deep for a single-pole drop. Two columns spread the load, allowing up to 300 lbs and screens typically 55 in to 100 in. It accepts VESA patterns from 200 x 100 mm to 800 x 400 mm and provides height adjustment plus tilt from +7.5 to -20 degrees, so screens can be angled toward the audience below. Post-installation roll adjustment makes final leveling quick after the display is hung. The...

The Chief XFA1UB is a Fusion extra-large floor support that carries a single large display on the floor rather than on the wall, ideal where walls cannot bear the load or where a heavy interactive panel needs a stable base. It handles screens typically 55 in to 100 in and up to 300 lbs, with VESA patterns from 200 x 200 mm to 800 x 400 mm. Manual height adjustment, backed by micro-adjustment, lets you set the screen at the right height for the room and its users. With a slim 6.3 in depth and a...

The Chief XFD1U is an extra-large floor support with motorized height adjustment, part of Chief's Electric Height Adjustable family alongside the XPD1U cart and XSD1U wall mount. It holds a single large display or interactive panel up to 310 lbs and accepts VESA patterns from 200 x 200 mm to 860 x 510 mm, which covers many large-format touch screens. Raising or lowering the display electrically makes it easy to adapt a screen to different users, from standing presenters to seated or younger...

The Chief XPA1UB is the black version of Chief's Fusion extra-large manual height adjustable cart, built to move big displays between rooms or reposition them within a space. It supports screens typically 55 in to 100 in and up to 300 lbs, with a universal interface covering VESA patterns from 200 x 200 mm to 800 x 400 mm. Manual height adjustment with micro-adjustment lets you set the screen at the right level for presenters, seated audiences or touch interaction. The cart's clean, rounded...

The Chief XPA1US is a Fusion extra-large mobile cart with rounded edges and a refined look that suits corporate offices and classrooms. Height is adjusted by one person using a 1/2 in hex bit on a power drill, with no need to remove the display. Compared with Chief's base XPA cart footprint, this version adds magnetic covers and handles for a cleaner appearance and easier moving. It supports screens typically 55 in to 100 in and up to 300 lbs, with VESA patterns from 200 x 200 mm to 800 x 400...

The Chief XPD1U is a Fusion extra-large mobile cart with motorized height adjustment, built to make interactive displays accessible to everyone in a classroom or boardroom. It delivers 26 in of electric vertical lift, controlled from an included integrated control pad, with optional PACREM remote or PACBLU Bluetooth dongle for the LINAK smartphone app sold separately. Anti-collision technology halts and reverses motion when it meets an obstruction, helping protect fingers and the display. The...

The Chief XSD1U is an extra-large wall mount with motorized height adjustment, the wall-mounted member of Chief's Electric Height Adjustable series that also includes the XPD1U cart and XFD1U floor support. It lets a large display or interactive panel move up and down at the touch of a control, so the screen can suit standing presenters, seated participants or younger students. The mount is designed for screens typically 50 in to 80 in, carries up to 310 lbs and accepts VESA patterns from 200...

The Chief XSM1U is a Fusion extra-large fixed wall mount that keeps large displays close to the wall at just 2.25 in deep. It supports screens typically 55 in to 100 in and up to 250 lbs, with a universal interface spanning VESA patterns from 100 x 100 mm to 1070 x 600 mm. Although the mount is fixed rather than tilting, it still offers height adjustment, micro-adjustment and 21.4 in of lateral shift so you can center and level the display precisely after it is hung. The wall plate fits stud...