Mounts & Racks

The Chief CMS006009 is a telescoping extension column from Chief's CMS series. It is a short pipe section used to lower a projector or display mount below a ceiling plate or structure, letting you fine-tune drop distance without ordering a longer custom column. Its telescoping design covers any length from 6 in to 9 in, so the final height can be dialed in on site rather than measured exactly in advance. The column measures 2.3 in across, carries a rated 500 lbs (226.8 kg) load and ships in a...

The Chief CMS006009W is an adjustable extension column that sets the drop between a ceiling plate or adapter and a Chief projector or display mount anywhere from 6 to 9 inches. Two telescoping tubes, a 2.3-inch outer column over a smaller inner column, let the installer fine-tune height on site instead of ordering an exact length. Length is locked with a screw through either of two adjustment holes for 1-inch steps or through a locking slot for 2-inch steps, then secured with set screws; both...

The Chief CMS006W is a 6-inch fixed-length extension column that sets a consistent drop between a ceiling plate or adapter and a Chief projector or flat panel ceiling mount. When the required distance is known, a fixed column keeps the install simple: one piece of pipe with standard 1-1/2 inch NPT threads at each end, which must engage at least four full threads into the plate or adapter. Chief rates CMS columns to a 500 lb combined load, limited by the lowest-rated component and by the...

The Chief CMS009 is a 9-inch fixed-length extension column that sets a consistent drop between a ceiling plate or adapter and a Chief projector or flat panel ceiling mount. When the required distance is known, a fixed column keeps the install simple: one piece of pipe with standard 1-1/2 inch NPT threads at each end, which must engage at least four full threads into the plate or adapter. Chief rates CMS columns to a 500 lb combined load, limited by the lowest-rated component and by the...

The Chief CMS009012 is an adjustable extension column that sets the drop between a ceiling plate or adapter and a Chief projector or display mount anywhere from 9 to 12 inches. Two telescoping tubes, a 2.3-inch outer column over a smaller inner column, let the installer fine-tune height on site instead of ordering an exact length. Length is locked with a screw through either of two adjustment holes for 1-inch steps or through a locking slot for 2-inch steps, then secured with set screws; both...

The Chief CMS009012W is an adjustable extension column that sets the drop between a ceiling plate or adapter and a Chief projector or display mount anywhere from 9 to 12 inches. Two telescoping tubes, a 2.3-inch outer column over a smaller inner column, let the installer fine-tune height on site instead of ordering an exact length. Length is locked with a screw through either of two adjustment holes for 1-inch steps or through a locking slot for 2-inch steps, then secured with set screws; both...

The Chief CMS009W is a 9-inch fixed-length extension column that sets a consistent drop between a ceiling plate or adapter and a Chief projector or flat panel ceiling mount. When the required distance is known, a fixed column keeps the install simple: one piece of pipe with standard 1-1/2 inch NPT threads at each end, which must engage at least four full threads into the plate or adapter. Chief rates CMS columns to a 500 lb combined load, limited by the lowest-rated component and by the...

The Chief CMS012 is a 12-inch fixed-length extension column that sets a consistent drop between a ceiling plate or adapter and a Chief projector or flat panel ceiling mount. When the required distance is known, a fixed column keeps the install simple: one piece of pipe with standard 1-1/2 inch NPT threads at each end, which must engage at least four full threads into the plate or adapter. Chief rates CMS columns to a 500 lb combined load, limited by the lowest-rated component and by the...

The Chief CMS012018 is an adjustable extension column that sets the drop between a ceiling plate or adapter and a Chief projector or display mount anywhere from 12 to 18 inches. Two telescoping tubes, a 2.3-inch outer column over a smaller inner column, let the installer fine-tune height on site instead of ordering an exact length. Length is locked with a screw through either of two adjustment holes for 1-inch steps or through a locking slot for 2-inch steps, then secured with set screws; both...

The Chief CMS012018W is an adjustable extension column that sets the drop between a ceiling plate or adapter and a Chief projector or display mount anywhere from 12 to 18 inches. Two telescoping tubes, a 2.3-inch outer column over a smaller inner column, let the installer fine-tune height on site instead of ordering an exact length. Length is locked with a screw through either of two adjustment holes for 1-inch steps or through a locking slot for 2-inch steps, then secured with set screws;...

The Chief CMS012W is a 12-inch fixed-length extension column that sets a consistent drop between a ceiling plate or adapter and a Chief projector or flat panel ceiling mount. When the required distance is known, a fixed column keeps the install simple: one piece of pipe with standard 1-1/2 inch NPT threads at each end, which must engage at least four full threads into the plate or adapter. Chief rates CMS columns to a 500 lb combined load, limited by the lowest-rated component and by the...

The Chief CMS018 is a 18-inch fixed-length extension column that sets a consistent drop between a ceiling plate or adapter and a Chief projector or flat panel ceiling mount. When the required distance is known, a fixed column keeps the install simple: one piece of pipe with standard 1-1/2 inch NPT threads at each end, which must engage at least four full threads into the plate or adapter. Chief rates CMS columns to a 500 lb combined load, limited by the lowest-rated component and by the...

The Chief CMS018024 is an adjustable extension column that sets the drop between a ceiling plate or adapter and a Chief projector or display mount anywhere from 18 to 24 inches. Two telescoping tubes, a 2.3-inch outer column over a smaller inner column, let the installer fine-tune height on site instead of ordering an exact length. Length is locked with a screw through either of two adjustment holes for 1-inch steps or through a locking slot for 2-inch steps, then secured with set screws; both...

The Chief CMS018024W is an adjustable extension column that sets the drop between a ceiling plate or adapter and a Chief projector or display mount anywhere from 18 to 24 inches. Two telescoping tubes, a 2.3-inch outer column over a smaller inner column, let the installer fine-tune height on site instead of ordering an exact length. Length is locked with a screw through either of two adjustment holes for 1-inch steps or through a locking slot for 2-inch steps, then secured with set screws;...

The Chief CMS018W is a 18-inch fixed-length extension column that sets a consistent drop between a ceiling plate or adapter and a Chief projector or flat panel ceiling mount. When the required distance is known, a fixed column keeps the install simple: one piece of pipe with standard 1-1/2 inch NPT threads at each end, which must engage at least four full threads into the plate or adapter. Chief rates CMS columns to a 500 lb combined load, limited by the lowest-rated component and by the...

The Chief CMS0203 is an adjustable extension column that sets the drop between a ceiling plate or adapter and a Chief projector or display mount anywhere from 24 to 36 inches. Two telescoping tubes, a 2.3-inch outer column over a smaller inner column, let the installer fine-tune height on site instead of ordering an exact length. Length is locked with a screw through either of two adjustment holes for 1-inch steps or through a locking slot for 2-inch steps, then secured with set screws; both...

The Chief CMS0203W is an adjustable extension column that sets the drop between a ceiling plate or adapter and a Chief projector or display mount anywhere from 24 to 36 inches. Two telescoping tubes, a 2.3-inch outer column over a smaller inner column, let the installer fine-tune height on site instead of ordering an exact length. Length is locked with a screw through either of two adjustment holes for 1-inch steps or through a locking slot for 2-inch steps, then secured with set screws; both...

The Chief CMS024 is a 24-inch (2-foot) fixed-length extension column in Chief's CMS series. It is the drop pipe that lowers a projector or flat panel mount from the structure above to the height you need, whether you are clearing a suspended ceiling, getting a projector into the correct throw position, or lining a display up with a sight line. Both ends carry standard 1-1/2-inch NPT threads, so the column screws into a Chief ceiling plate or structural adapter at the top and the mount's column...

The Chief CMS024W is a 24-inch (2-foot) fixed-length extension column in Chief's CMS series. It is the drop pipe that lowers a projector or flat panel mount from the structure above to the height you need, whether you are clearing a suspended ceiling, getting a projector into the correct throw position, or lining a display up with a sight line. Both ends carry standard 1-1/2-inch NPT threads, so the column screws into a Chief ceiling plate or structural adapter at the top and the mount's...

The Chief CMS0305 is a telescoping extension column in Chief's CMS series that adjusts from 3 to 5 feet. It lowers a projector or flat panel mount from a ceiling plate or structural adapter, and because the length is set during installation you do not have to know the exact drop before ordering. The column is made of two nested tubes. Once the mount is at the right height, a screw through an adjustment hole and a pair of set screws lock the tubes together; Chief supplies both standard and...

The Chief CMS0305W is a telescoping extension column in Chief's CMS series that adjusts from 3 to 5 feet. It lowers a projector or flat panel mount from a ceiling plate or structural adapter, and because the length is set during installation you do not have to know the exact drop before ordering. The column is made of two nested tubes. Once the mount is at the right height, a screw through an adjustment hole and a pair of set screws lock the tubes together; Chief supplies both standard and...

The Chief CMS036 is a 36-inch (3-foot) fixed-length extension column in Chief's CMS series. It is the drop pipe that lowers a projector or flat panel mount from the structure above to the height you need, whether you are clearing a suspended ceiling, getting a projector into the correct throw position, or lining a display up with a sight line. Both ends carry standard 1-1/2-inch NPT threads, so the column screws into a Chief ceiling plate or structural adapter at the top and the mount's column...

The Chief CMS036W is a 36-inch (3-foot) fixed-length extension column in Chief's CMS series. It is the drop pipe that lowers a projector or flat panel mount from the structure above to the height you need, whether you are clearing a suspended ceiling, getting a projector into the correct throw position, or lining a display up with a sight line. Both ends carry standard 1-1/2-inch NPT threads, so the column screws into a Chief ceiling plate or structural adapter at the top and the mount's...

The Chief CMS0406 is a telescoping extension column in Chief's CMS series that adjusts from 4 to 6 feet. It lowers a projector or flat panel mount from a ceiling plate or structural adapter, and because the length is set during installation you do not have to know the exact drop before ordering. The column is made of two nested tubes. Once the mount is at the right height, a screw through an adjustment hole and a pair of set screws lock the tubes together; Chief supplies both standard and...