Automation

The Blustream IP50HD-RX is the receiver for the Contractor Series IP50 platform, an affordable way to distribute 1080p HDMI over standard 100Mbps network infrastructure. It decodes H.265 video from IP50HD-TX transmitters, scales it to the attached display, and passes IR, RS-232 and USB/KVM. It can run as part of a networked matrix or as a direct point-to-point extender.Key FeaturesLatency of 3 frames (under 120ms, depending on compression, frame rate and scaling)PCM 2.0 channel audioMatrix...

The Blustream IP50HD-TX is the transmitter for the Contractor Series IP50 platform. It compresses a 1080p HDMI source with H.265 so it can travel over ordinary 100Mbps network infrastructure, unicast on unmanaged networks or multicast on managed ones. A zero-latency HDMI loop-out feeds a local display, and IR, RS-232 and USB/KVM travel with the video.Key FeaturesLatency of 3 frames (under 120ms), none on the loop-outPCM 2.0 channel audioMatrix distribution through a 100Mbps switch, or...

The Blustream IP510UHD-TZ is an SDVoE video over IP transceiver for 10Gb managed networks. Each unit has both an HDMI input and an HDMI output, so it can act as a transmitter and receiver at the same time. It passes 4K 60Hz 4:4:4 HDMI 2.0 with HDR, multichannel audio and control signals, and supports matrix switching, video walls and multiview, or works as a direct one-to-one extender without a switch.Key FeaturesDolby Vision and HDR require Genlock modeSupports Dolby Atmos, Dolby TrueHD,...

The Blustream IRDE1 is a 5V designer IR emitter that sticks onto the IR window of a source or display and repeats commands from a Blustream matrix, extender or video over IP unit. A visible red LED shows when IR is being sent, which makes commissioning and troubleshooting quicker.Key Features5V operation3.5mm mono plugAdhesive backing includedRed indicator LEDIdeal ApplicationsControlling sources in a rack from a remote zoneDisplay control at the far end of an HDBaseT or IP linkReplacement or...

The Blustream IRDIR is a designer-style 5V IR receiver for capturing handheld remote commands and feeding them into the IR input of a Blustream matrix, extender or switcher. It sticks in place with its adhesive backing, and a recessed cable channel lets the lead leave the receiver either vertically or horizontally for a tidy install.Blustream states that most of its IR products run on a 5V line. For 12V third-party control systems, Blustream directs installers to its IR-CAB 12V-to-5V link...

The Blustream IRE1 is a 5V single IR emitter that carries routed IR commands from a Blustream matrix, extender or switcher to the IR window of a source device. It terminates in a 3.5mm mono plug and is built for short-range, discreet control of a single device.Blustream notes that its 5V IR cabling can be damaged if connected to a product set for 12V IR, so confirm the IR voltage setting on switchable products before installing.Key Features5V operation3.5mm mono jack20kHz to 55kHz carrier...

The Blustream IRE2 is a 5V twin IR emitter that carries routed IR commands from a Blustream matrix, extender or switcher to the IR window of a source device. Its two emitter buds share one 3.5mm mono plug, so one IR output can drive two pieces of equipment in the same rack or cabinet.Blustream notes that its 5V IR cabling can be damaged if connected to a product set for 12V IR, so confirm the IR voltage setting on switchable products before installing.Key Features5V operation3.5mm mono...

The Blustream IRR is the standard 5V IR receiver used across the Blustream range. It picks up handheld remote commands at a display or room location and passes them into the IR input of a Blustream matrix, HDBaseT receiver or switcher over a 3.5mm stereo connection.For 12V third-party control systems, Blustream directs installers to its IR-CAB 12V-to-5V link cable rather than connecting 5V cabling to a 12V source.Key Features5V operation3.5mm stereo jack (signal, ground and 5V)20kHz to 55kHz...

The Blustream MFP62 gathers laptop and room sources into one presentation switcher. Three HDMI inputs sit alongside USB-C (DP 1.2 Alt mode), DisplayPort and VGA, and any of them can be sent to two scaled HDMI outputs at up to 4K 60Hz 4:4:4.Audio is handled in the same box. A mic input supports line level, 48V phantom power or balanced/unbalanced mono, and an audio mixer sets independent levels. The unit can embed analogue audio and break out audio to analogue L/R and coaxial S/PDIF at the same...

The Blustream MV41 is a 4x1 HDMI multiview switcher that puts up to four HDMI 2.0 sources on a single screen at once. Choose from preset or custom PIP, PBP, POP, dual, triple and quad window layouts, with seamless switching between them.Every input has its own HDMI loop-out for a local display or for cascading to other equipment. Audio from the selected source breaks out to balanced or unbalanced analogue L/R and optical S/PDIF at the same time.Key Features4 x HDMI inputs, 1 x multiview...

The Blustream MX22AB-8K is a compact 2x2 HDMI 2.1 matrix for the latest 8K and high-frame-rate sources. Two inputs route independently to two outputs at up to 40Gbps, carrying 8K 60Hz, 8K 30Hz 4:4:4 or 4K 120Hz 4:4:4 with HDR, plus ALLM and VRR for gaming consoles and PCs.It can switch automatically when it detects a new 5V hot plug or TMDS signal, or manually from the front panel, IR or RS-232. Audio breaks out to analogue L/R and optical S/PDIF at the same time for a soundbar or AV...

The Blustream MX44AVW is a 4K HDMI 2.0 video processor that can run as a 4x4 seamless switching matrix, an advanced video wall processor or a quad multiview system. In video wall mode individual panels can be overlapped and rotated, which suits creative and portrait wall layouts.Multiview mode offers preset and custom PIP, POP, PBP, dual, triple and quad windows. Blustream notes that 1080i works in matrix and multiview modes but not in video wall mode.Key Features4K HDMI 2.0 processing for...

The Blustream MX44KVM is a 4x4 USB 3.0 matrix that lets four host computers share four USB peripherals such as keyboards, mice, cameras or touch panels. Transfer rates reach 5Gbps and it is backward compatible with USB 2.0 and 1.1, with no drivers needed.An RS-232 loop-through repeats incoming commands to other Blustream products, and its inputs and outputs can be assigned so it follows a Blustream video matrix for full KVM switching. Four configurable GPIO ports allow integration with...

The Blustream PAC500AU is a passive audio-over-CAT extender kit for moving stereo analogue audio a long way with minimal fuss. A pair of compact units converts RCA left/right audio onto a single CAT cable and back again, reaching up to 500m.Because it is passive there is nothing to power at either end, and either unit can serve as the transmitter or receiver.Key FeaturesUp to 500m over a single CAT cablePassive, no power requiredRCA L/R input and outputRJ45 CAT linkInterchangeable TX and RX...

The Blustream PLA88CS is the Platinum 8x8 4K HDMI 2.0 HDBaseT matrix. Over a single CAT cable it carries HDMI, ARC, LAN, two-way IR and RS-232 and PoC, reaching 150m at 1080p or 100m at 4K 60Hz 4:4:4 using Long Range Mode with the recommended RX150CS receiver.Eight HDMI inputs plus two remote HDBaseT inputs route to eight HDBaseT outputs, four of which are mirrored on HDMI for dual displays per zone. Each HDBaseT output scales independently, and a separate audio matrix with Dolby and DTS...

The Blustream POC11 sits in an HDBaseT line and injects 12V or 24V DC so a Blustream HDBaseT transmitter can be powered remotely, removing the need for a power outlet behind the source.It passes 18Gbps 4K video, multichannel audio and HDCP 2.2. Blustream specifies a maximum of 30m from the POC11 to the transmitter and 70m to the receiver, and notes it is designed for Blustream products and may not work with other HDBaseT extenders.Key FeaturesSelectable 12V or 24V via 3-step switchCompatible...

The PRO-8AB adds zone audio breakout to a Custom Pro matrix, pulling the HDMI audio from each of the 8 video zone outputs and presenting it as coaxial digital and analog stereo for local amplifiers or audio systems.Key FeaturesBreaks out audio from 8 video zone outputsCoaxial digital and analog L/R per zoneNo DSP processingQuick-release card fittings for the Custom Pro Matrix hubIdeal ApplicationsBuilding or expanding a Blustream Custom Pro matrixReplacing or upgrading a board in an installed...

The PRO-8ABV gives each Custom Pro video zone its own audio feed with adjustable analog level, so the matrix can drive local amplifiers or soundbars at a controlled volume alongside a coaxial digital output.Key FeaturesVariable line-level control on analog outputsCoaxial digital and analog L/R per zone2-channel PCM on analog outputsQuick-release card fittings for the Custom Pro Matrix hubIdeal ApplicationsBuilding or expanding a Blustream Custom Pro matrixReplacing or upgrading a board in an...

The PRO-8IR-V2 handles IR routing inside a Custom Pro matrix, sending control from each zone back to the sources in the rack and passing IR out to the HDBaseT receivers. 12V operation requires compatible IR hardware and receivers.Key FeaturesBi-directional IR routing5V or 12V selectableRouted control of local source hardwareQuick-release card fittings for the Custom Pro Matrix hubIdeal ApplicationsBuilding or expanding a Blustream Custom Pro matrixReplacing or upgrading a board in an installed...

The PRO-8RS232 adds per-zone serial control to a Custom Pro matrix, giving each of 8 compatible Blustream HDBaseT receivers its own two-way RS-232 path for controlling displays or other zone devices.Key Features8 bi-directional RS-232 portsPhoenix terminal connectionsQuick-release card fittings for the Custom Pro Matrix hubIdeal ApplicationsBuilding or expanding a Blustream Custom Pro matrixReplacing or upgrading a board in an installed Custom Pro systemTailoring a Custom Pro hub to a specific...

The PRO-IN2H2TCS lets a Custom Pro matrix accept remote sources over HDBaseT alongside local HDMI sources. Each of its four inputs routes independently to any HDMI or HDBaseT output board, and the HDBaseT inputs carry IR for controlling the source at each transmitter.Key FeaturesRemote source inputs via compatible Blustream CSC transmittersBitstream passthrough of multichannel and object-based audioPer-input fixed-level analog audio breakout (2ch PCM)Quick-release card fittings for the Custom...

The PRO-IN2HAB adds two local HDMI 2.0 sources to a Custom Pro matrix, with a separate analog stereo feed from each input for a third-party audio system. Full 18Gbps operation needs an 18Gbps Custom Pro output board.Key FeaturesIndependent routing to any HDMI or HDBaseT output boardPer-input 2ch PCM analog breakoutPasses multichannel surround formatsQuick-release card fittings for the Custom Pro Matrix hubIdeal ApplicationsBuilding or expanding a Blustream Custom Pro matrixReplacing or...

The PRO-IN4HAB is the standard four-source HDMI 2.0 input card for the Custom Pro matrix and is the input board supplied in Blustream's pre-built Custom Pro systems. Full 18Gbps operation needs an 18Gbps Custom Pro output board.Key FeaturesIndependent routing to any HDMI or HDBaseT output boardPer-input 2ch PCM analog breakoutPasses multichannel surround formatsQuick-release card fittings for the Custom Pro Matrix hubIdeal ApplicationsBuilding or expanding a Blustream Custom Pro...

The PRO-IN4HDA brings Dante networked audio into a Custom Pro matrix. Source audio can be sent onto the Dante network per input, and Dante audio can be embedded back onto HDMI for distribution to displays and zones.Key FeaturesDante breakout and embedding on one boardRJ45 LAN port for Dante audioIndependent routing to any HDMI or HDBaseT output boardQuick-release card fittings for the Custom Pro Matrix hubIdeal ApplicationsBuilding or expanding a Blustream Custom Pro matrixReplacing or...