Crestron

Crestron C2N-RTSCresnet Temperature SensorThe C2N-RTS is a wall-mount temperature sensor that supplies ambient room temperature readings to a Crestron control system. It provides the measurement data automation programs need for HVAC control, comfort scheduling, and temperature monitoring in residential and commercial spaces.Connecting over the four-wire Cresnet bus, the sensor draws its power and communicates on the same cable, keeping installation simple. Its compact enclosure mounts...

Crestron C3COM-33-Series Serial COM Expansion CardThe C3COM-3 is a 3-Series expansion card that adds three bidirectional serial communication ports to a compatible Crestron control system. It plugs into an available card slot and extends the processor's ability to command projectors, displays, matrix switchers, and other serial-controlled equipment.Each of the three ports supports RS-232, RS-422, and RS-485 signaling with configurable baud rates up to 115.2k, along with hardware and software...

Crestron C3RY-163-Series Relay Output CardThe C3RY-16 is a 3-Series expansion card that provides sixteen isolated relay outputs to a compatible Crestron control system. It plugs into an available card slot and gives the processor direct low-voltage switching control over motorized and contact-driven equipment.Each normally open, isolated relay is rated for 1 A at 30 VDC, making the card well suited to triggering projection screens, lifts, drapery motors, contactors, and similar loads. By...

Crestron C3RY-83-Series Relay Output CardThe C3RY-8 is a 3-Series expansion card that adds eight isolated relay outputs to a compatible Crestron control system. It installs in an available card slot and lets the processor directly control low-voltage switching for motorized and contact-driven devices.Each normally open, isolated relay is rated for 1 A at 30 VDC, suiting the card to switching projection screens, lifts, drapery motors, contactors, and comparable loads. The eight-relay format...

Crestron CB6SE-BTNB-S ENGRAVEDCameo Keypad Button SetThe CB6SE-BTNB-S ENGRAVED is a field-replaceable button set for Crestron Cameo backlit keypads, supplied in a smooth finish with engraving. It lets integrators fit a keypad with a six-button arrangement and clearly labeled caps that match a room's specific control functions.Because the caps install onto the keypad in the field, this set makes it easy to reconfigure or relabel an existing Cameo keypad without replacing the entire unit. The...

Crestron CBLR-DP-VTabletop DisplayPort Cable RetractorThe CBLR-DP-V is a tabletop cable retractor fitted with a DisplayPort cable, designed for vertical (below-surface) mounting in conference tables and lecterns. It keeps a ready DisplayPort connection at hand while eliminating the loose, tangled cabling that clutters shared presentation surfaces.When a presenter needs to connect, the cable pulls up from the retractor and feeds their device; when finished, it retracts neatly below the tabletop...

Crestron CBLR2-AudioTabletop Audio Cable RetractorThe CBLR2-Audio is a second-generation Crestron cable retractor equipped with a 3.5mm stereo analog audio cable for tabletop integration. It offers a clean, always-available way to patch a laptop or mobile device's audio into a room system without leaving cables strewn across the surface.The audio cable extends from the retractor when needed and draws back below the table when the connection is finished, keeping the work surface uncluttered and...

Crestron CBLR2-CAT5ETabletop CAT5e Cable RetractorThe CBLR2-CAT5E is a second-generation Crestron cable retractor fitted with a CAT5e Ethernet cable and RJ45 connector for tabletop integration. It provides a neat, always-ready wired network drop at the meeting surface while keeping the cabling managed and out of the way.The CAT5e cable pulls out from the retractor to connect a laptop or other device and then draws back below the tabletop when no longer in use, preserving a clean work surface...

Crestron CBLR2-HDTabletop HDMI Cable RetractorThe Crestron CBLR2-HD is a pull-out HDMI cable retractor from the Cable Retractor 2 Series, engineered to keep a permanently connected display cable tidy at the conference table or lectern. The captive HDMI lead extends smoothly to the presenter's laptop and springs back into the tabletop grommet when released, eliminating loose cabling, cutting connector wear, and preventing the cable losses that plague shared meeting spaces.Rated for HDMI signals...

Crestron CBLR2-USBTabletop USB Cable RetractorThe Crestron CBLR2-USB is a pull-out USB cable retractor from the Cable Retractor 2 Series, designed to deliver a clean, always-available USB connection at the meeting table. The captive lead pulls out to reach a user's laptop and retracts back into the tabletop mount when released, keeping the work surface uncluttered and protecting the connector from the wear caused by repeated plugging and unplugging.Ideal for USB-based conferencing peripherals,...

Crestron CBLR2-VGATabletop VGA Cable RetractorThe Crestron CBLR2-VGA is a pull-out VGA cable retractor from the Cable Retractor 2 Series, providing a permanently installed analog RGB connection for legacy laptops and sources at the conference table. The captive DE-15 (HD-15) lead extends to the presenter's device and retracts neatly into the tabletop mount when released, keeping the table surface clean and the cable from wandering off.Terminated with a standard 15-pin VGA connector, the...

Crestron CEN-GWEXER-PWEinfiNET EX / ER Wireless Gateway with PoE KitThe Crestron CEN-GWEXER-PWE is a wireless gateway that brings Crestron infiNET EX two-way mesh RF devices and ER one-way extended-range devices onto a control system over Ethernet. It serves as the RF hub for dimmers, keypads, thermostats, shades, and handheld remotes, coordinating reliable low-latency communication across a self-healing mesh that extends coverage as devices are added.Because it connects to the control...