Accessories

The QSC M10 KIT-W is an M10 forged-steel eyebolt suspension kit for vertically flying QSC loudspeakers such as the E112, E115 and E215, KW-series and AcousticPerformance cabinets. Supplied as a three-pack, it provides rated eyebolt hardware that threads into the factory M10 rigging inserts so integrators and rental crews can suspend cabinets overhead safely. This is rigging hardware only, not a loudspeaker.Key FeaturesM10 forged-steel eyebolt suspension kit (3-pack)For vertical orientation...

The QSC M8 KIT-A is a professional M8 steel eyebolt suspension kit for permanently or temporarily flying QSC E Series passive loudspeakers such as the E110, E112 and E115. It gives integrators and rental companies a rated, hardware-matched way to suspend cabinets from the factory M8 fly points, so it is an accessory, not a loudspeaker. The kit is supplied as a six-pack of forged eyebolts finished in black.Key FeaturesSix forged M8 steel eyebolts for suspending compatible QSC loudspeakersDesigne...

The QSC Axiom ML1 (Attero Tech) is a compact analog audio extension module that carries mic and line sources over standard Category cabling to a paired host unit such as the AXP2O. It is aimed at cost-conscious commercial installs in retail, restaurants, education and hospitality where local input connectivity is needed without running long analog home-runs.Key FeaturesXLR microphone input with adjustable gain for dynamic mics1/4" line input with fixed attenuation pad3.5 mm consumer input with...

The QSC PB2082-i is a pull-back bar (rigging accessory) for the QSC Installed Line Array (ILA) system. It attaches to the array to draw the lower enclosures back, letting installers dial in the desired inter-element splay angles for precise vertical coverage of a flown WL2082-i array. This is a hardware accessory, not a loudspeaker. This is the black finish version.Key FeaturesPull-back bar for setting array splay anglesRefines vertical coverage of a flown WL2082-i arrayWorks with the ILA...

The QSC PB2082-i is a pull-back bar (rigging accessory) for the QSC Installed Line Array (ILA) system. It attaches to the array to pull the lower enclosures back, allowing installers to set the inter-element splay angles for precise vertical coverage of a flown WL2082-i array. This is a hardware accessory, not a loudspeaker. This is the white finish version for white ILA systems.Key FeaturesPull-back bar for setting array splay anglesRefines vertical coverage of a flown WL2082-i arrayWorks...

The QSC PTZ-CMB1 is a ceiling mounting bracket accessory for QSC PTZ-IP conferencing cameras, finished in black. It lets integrators suspend a compatible PTZ camera from the ceiling for a clean, unobtrusive installation, using the camera's image-rotation feature for correct picture orientation. It is intended for conference rooms, lecture halls, and event spaces where a wall or shelf mount is not practical.Key FeaturesCeiling mount bracket for QSC PTZ-IP camerasEnables inverted ceiling...

The QSC SL-QSE-110-P is a Q-SYS Scripting Engine feature license for the Core 110f processor. It is a software license rather than a physical product, unlocking the Q-SYS Scripting Engine so integrators can run Lua-based custom logic and control on that Core. It is activated through the Q-SYS licensing system.Key FeaturesEnables the Q-SYS Scripting Engine on a Core 110fSupports Lua-based custom control and automation logicPerpetual license tied to the specified Core modelSoftware feature...

The QSC SL-QUD-110-P is a Q-SYS UCI Deployment feature license for the Core 110f processor. It is a software license, not a physical product, that unlocks the ability to deploy User Control Interfaces (UCIs) to compatible Q-SYS user control devices from that Core. It is delivered and activated through the Q-SYS licensing system.Key FeaturesEnables UCI (User Control Interface) deployment from a Core 110fPerpetual license tied to the specified Core modelSoftware feature license—no hardware...

The QSC SP-16x is a threaded loudspeaker pole extension used to raise a top-mounted speaker higher above a subwoofer or pole-mount base. It adds roughly 16 inches (about 41 cm) of height on a standard 35 mm diameter shaft, letting integrators and rental crews fine-tune the vertical position of a full-range cabinet for better sight lines and coverage. It is an accessory only, not a loudspeaker.Key FeaturesThreaded 35 mm diameter speaker pole extensionApproximately 16 in (41 cm) added...

The QSC SP-36 is a 36-inch (about 91 cm) threaded loudspeaker pole that mounts a full-range speaker on top of a subwoofer or pole-mount base. Built on a 35 mm diameter shaft with M20 threading, it is used across QSC portable and line-array systems to lift a top cabinet to ear level for cleaner coverage. It is a mounting accessory, not a powered or passive loudspeaker.Key Features36 in (91 cm) threaded speaker pole35 mm shaft with M20 threadPositions a top speaker above a subwoofer or...

The QSC TouchMix-30 Pro Dust Cover is a fitted fabric cover that protects the TouchMix-30 Pro digital mixer from dust and debris when the console is installed or stored. It slips over the mixer to keep the control surface and connectors clean between sessions, which is useful for fixed installs and studios where the console stays in place. This is a protective accessory, not a functional part of the mixer.Key FeaturesFitted fabric cover for the TouchMix-30 ProKeeps dust off the control surface...

The QSC TouchMix-30 Pro Tote is a padded carrying bag designed specifically for the TouchMix-30 Pro digital mixer. It protects the console during transport and storage with cushioned sides and a shaped interior that fits the mixer, making it easy for engineers and performers to move the console between gigs and rehearsals. This is a transport accessory for the mixer, not a mixer itself.Key FeaturesPadded tote sized for the TouchMix-30 ProProtects the console during transport and...

The QSC TouchMix-30 Tablet Support Stand (also sold as the TS-1) is an accessory for the QSC TouchMix-30 Pro digital mixer. It is a mounting stand, not electronic gear. The stand attaches to the mixer to hold a tablet at a comfortable viewing angle, letting engineers use QSC's TouchMix wireless control app alongside the mixer's own touchscreen. This makes it easier to run the console from the stage or the audience while keeping the tablet stable and within reach. It is a simple, purpose-built...

The QSC RP1 kit is a set of rear blanking plates (a four-pack) for Q-SYS Core and I/O card frames. It is an accessory, not an active device: the plates cover the open rear slots above any unused I/O card positions so a partially populated chassis stays closed, tidy and properly ventilated.Key FeaturesRear plate covers for Q-SYS Core / I/O card frame slotsSupplied as a four-pack of blank platesCloses empty card openings on partially loaded chassisMaintains a clean rear appearance and correct...

The QSC SL-DAN-16-P is a Q-SYS Software-based Dante license that adds 16 x 16 (16 in, 16 out) bidirectional Dante network audio channels to a compatible Q-SYS Core. It is a software/feature license rather than a physical device, activated through the Q-SYS licensing system, and requires no additional I/O hardware.Key FeaturesAdds 16 x 16 Dante audio channels to a Q-SYS CoreSoftware-based—no extra cards or hardware requiredPerpetual, node-locked license tied to a specific CoreLets...

The QSC SL-DAN-32-P is a Q-SYS Software-based Dante license that adds 32 x 32 (32 in, 32 out) bidirectional Dante network audio channels to a compatible Q-SYS Core. It is a software/feature license, not a physical device, and is activated through the Q-SYS licensing system with no additional I/O hardware.Key FeaturesAdds 32 x 32 Dante audio channels to a Q-SYS CoreSoftware-based—no extra cards or hardware requiredPerpetual, node-locked license tied to a specific CoreIdeal for larger...

The QSC SL-DAN-8-P is a Q-SYS Software-based Dante license that adds 8 x 8 (8 in, 8 out) bidirectional Dante network audio channels to a compatible Q-SYS Core without any additional hardware. It is a software/feature license, not a physical device, and is delivered and activated through the Q-SYS licensing system.Key FeaturesAdds 8 x 8 Dante audio channels to a Q-SYS CoreSoftware-based—no I/O cards or extra hardware requiredPerpetual, node-locked license tied to a specific CoreLets...

The QSC SL-QSE-510-P is a Q-SYS Scripting Engine feature license for the Core 510i processor. It is a software license rather than a physical product, unlocking the Q-SYS Scripting Engine so integrators can run Lua-based custom logic, integrations and automation on that Core. It is activated through the Q-SYS licensing system.Key FeaturesEnables the Q-SYS Scripting Engine on a Core 510iSupports Lua-based custom control and automation logicPerpetual license tied to the specified Core...

The QSC SL-QUD-510-P is a Q-SYS UCI Deployment feature license for the Core 510i processor. It is a software license, not a physical product, that unlocks the deployment of User Control Interfaces (UCIs) to compatible Q-SYS control devices from that Core. It is delivered and activated through the Q-SYS licensing system.Key FeaturesEnables UCI (User Control Interface) deployment from a Core 510iPerpetual license tied to the specified Core modelSoftware feature license—no hardware...

This is an installation accessory, not a speaker or an amplifier. The Sonance In-Wall Back Box is an enclosure designed to house a Sonos Amp inside a wall cavity, so the amplifier can live at the point of use rather than in a rack or an equipment closet. It is part of the Sonos Architectural line, which Sonos and Sonance developed together, and it is sold as a single unit in black.The intended use case is a clean, permanent install: a whole-home audio zone, a conference or huddle room, a...

This is a mounting accessory for the Sonos Arc Ultra and Arc soundbars - the soundbar itself is sold separately. Sonos designed the bracket specifically for these two models, which matters because Arc and Arc Ultra fire audio upward and sideways as well as forward; a generic soundbar bracket can sit the bar at the wrong height or angle and compromise the reflected channels that produce the Dolby Atmos effect.The mount holds the bar tight and flat against the wall beneath a TV, at the low...

This is a mounting accessory for the Sonos Beam soundbar; the Beam itself is sold separately. The bracket is designed by Sonos to hold Beam flat and close to the wall below a television, giving the near-invisible look that a purpose-built mount achieves and a generic universal bracket usually does not.The design goal is acoustic as much as visual. A soundbar resting on a media console can couple with the furniture surface and produce audible rattle at higher volumes, particularly on bass-heavy...

This is a mounting accessory for the Sonos Beam soundbar - the Beam is sold separately. Sonos designed the bracket around Beam's exact cabinet, so the bar sits flat and tight to the wall under a television with a low, near-invisible profile that universal soundbar brackets rarely match.There is an acoustic reason to mount rather than shelve. A soundbar sitting on a media console can couple with the furniture and produce audible rattle on bass-heavy content, and a console surface also puts the...

This is a pair of replacement grilles for 8-inch In-Ceiling Speakers by Sonos and Sonance - a finishing part, not a speaker. It is the correct item when original grilles have been damaged, dented, over-painted, corroded in a humid room, or lost during a remodel, and it is also useful when a room is being repainted and you would rather start with fresh grilles than mask and spray the existing ones.The grilles use the trimless design of the Sonos Architectural range, sitting flush with the...