This item is discontinued/limited supply. Please chat with us to see if we have them or a replacement.

2x210W Commercial Power Amplifier, 4/8

Get Custom Programming from 4TEC

Price: $1,250.00
    Quantity:
    Availability: In Stock
    Usually ships In 24 - 48 hours

    Item #: AMP-2210S

    Crestron AMP-series Commercial Power Amplifiers provide a perfect combination of high output and efficiency for all types of professional audio applications. 100% Crestron engineered and built, these amplifiers are ENERGY STAR qualified to enable organizations to fulfill their green initiatives without compromising on audio performance. Advanced design features include a high-efficiency amp topology with active power factor corrected power supply, delivering a generous amount of power in a space-saving 1U rack-mountable chassis.

    Audio

    • Typical of 2 mono amplifier channels:
    • Input Signal Type Balanced or unbalanced analog line-level
    • Output Signal Type 4/8 Ohm
    • Output Power 120 Watts at 8 Ohms;
    • 210 Watts at 4 Ohms;
    • 420 Watts at 8 Ohms bridged
    • Damping Factor >100
    • Protection Over Current, Over/Under Voltage, Over Temperature, DC Offset
    • Frequency Response 20Hz to 20kHz 0.5 dB
    • THD 0.05% @ 1kHz, full rated power at 4/8 Ohms or 8 Ohms Bridged;
    • 0.1% @ 20Hz to 20kHz, 120W at 8 Ohms;
    • 0.2% @ 20Hz to 20kHz, 210W at 4 Ohms;
    • 0.1% @ 20Hz to 20kHz, 420W at 8 Ohms Bridged
    • S/N Ratio >103 dB, A-weighted
    • Crosstalk >70 dB @ 1kHz
    • Gain 23 dB with INPUT LEVEL control set at 12 o'clock nominal position
    • Input Sensitivity 2.22 Vrms for rated output power with INPUT LEVEL control set at 12 o'clock nominal position
    • Input Detection Threshold 40 mV RMS @ 1 kHz
    • Input Level Adjustment 10 dB from nominal
    Connectors
    • G 6-32 screw, chassis ground lug
    • INPUT CH 1 – 2 (2) 3-pin 3.5mm detachable terminal blocks;
    • Balanced/unbalanced line-level audio inputs;
    • Input Level: 5.3 Vrms maximum with INPUT LEVEL control set at minimum position;
    • Input Impedance: 24k Ohms balanced, 12k Ohms unbalanced
    • SPEAKER OUTPUT CH 1 – 2 (2) 2-pin 7.62mm 15A detachable terminal blocks;
    • 4/8 and 70/100V power amplifier outputs;
    • Wire Size: Terminals accept up to 14 AWG
    • REMOTE (1) 6-pin 3.5mm detachable terminal block;
    • Provides (2) remote control inputs; enables independent power control of each channel via local jumpers or remote contact closures;
    • inputs may be safely paralleled for global control
    • FUSE T6.3AH 250V Main fuse holder;
    • 5x20 mm, 250V, 6.3AH, time-lag, high-rupture rated
    • 100-240V~50/60Hz (1) IEC C14 male chassis plugs, main power input;
    • Mates with removable power cord (included)
    Controls & Indicators
    • PWR (1) dual-color LED, green indicates ACTIVE state, yellow indicates STANDBY state
    • INPUT 1 – 2, SIGNAL (2) green LEDs, indicate signal presence on each corresponding channel
    • OUTPUT 1 – 2, CLIP (2) amber LEDs, indicate a clipping condition on each corresponding channel
    • OUTPUT 1 – 2, FAULT (2) red LEDs; indicate over-temperature, over-current, over or under power supply voltage, or DC offset condition on each corresponding channel
    • INPUT CH 1 – 2 LEVEL (rear) (2) Rotary input boost/attenuate adjustments w/center detent at nominal
    • ON/REMOTE/OFF (rear) (1) 3-position slide switch; selects between all channels powered on, all channels powered off, or remote control of each individual channel
    Power Requirements
    • Main Power 100-240 Volts AC, 50/60 Hz
    • Power Consumption 62 Watts @ 8 Ohms, all channels driven at 1/8th output power;
    • 88 Watts @ 4 Ohms, all channels driven at 1/8th output power;
    • 26 Watts, all channels idle;
    • <1 Watt in standby
    Environmental
    • Temperature 41° to 104°F (5° to 40°C)
    • Humidity 10% to 90% RH (non-condensing)
    • Heat Dissipation 110 BTU/Hr @ 8 Ohms, all channels driven at 1/8th output power;
    • 121 BTU/Hr @ 4 Ohms, all channels driven at 1/8th output power;
    • 89 BTU/Hr, all channels idle;
    • <3.4 BTU/Hr in standby
    Enclosure
    • Chassis Metal with black finish, vented top and sides, convection cooled
    • Front Panel Metal, black finish with polycarbonate label overlay
    • Mounting Freestanding or 1U 19-inch rack-mountable (adhesive feet and rack ears included)
    Dimensions
    • Height 1.70 in (44 mm)
    • Width 17.28 in (439 mm);
    • 19.0 in (483 mm) with rack ears
    • Depth 10.34 in (263 mm)
    Weight
    • 8.1 lb (3.7 kg)

    Key Features

    • ENERGY STAR® qualified power amplifier
    • Ultra-efficient space-saving design
    • Low total cost of ownership
    • High-output power, low noise, low distortion performance
    • Two channels each rated 210W@4 and 120W@8
    • Bridgeable for 420W@8
    • Individual channel power control via jumper or remote contact
    • Auto power-down after 30 minutes of no signal
    • Instant auto power-on when an input signal is detected
    • No inrush current during power-up
    • Over current and DC offset protection per output
    • Thermal protection on the power supply and each channel
    • Front panel signal, clip, and fault indicators per channel
    • Professional balanced inputs
    • Detachable terminal block connectors
    • Rear panel 10dB input level controls
    • Convection cooled - no noisy fans
    • Single-space 1U rack mountable
    • Lightweight and under 11 inches deep
    • Universal power supply with active power factor correction