The HD-MD4X4-4KZ-E is a 4K60 4:4:4 HDR (High Dynamic Range) AV switcher that provides a cost-effective solution for professional AV applications. Equipped with four HDMI® inputs and four HDMI outputs, the HD-MD4X4-4KZ-E includes features such as EDID management, HDCP 2.3 compliance, enterprise-grade security, and XiO Cloud® service support.
4K60 4:4:4 and HDR Support
The HD-MD4X4-4KZ-E supports video resolutions up to 4K60 with 4:4:4 color sampling. HDR10, HDR10+, and Dolby Vision® video formats are also supported.
EDID Management
The HD-MD4X4-4KZ-E provides comprehensive management of EDID (Extended Display Identification Data) to ensure that every source is displayed at the optimal resolution and format. For applications requiring a custom configuration, the HD-MD4X4-4KZ-E enables assessment of the format and resolution capabilities of any device that is connected to an HDMI output of the switcher. The HD-MD4X4-4KZ-E provides the ability to configure signals appropriately for the most desirable and predictable behavior.
HDMI Audio De-embedding
Embedded HDMI 2-channel LPCM audio can be extracted from the selected HDMI input and transmitted to either of the two AUX stereo audio outputs. Volume and mute control are configurable for each of the HDMI outputs and for each of the two AUX audio outputs independently.
Device Control via CEC
Under the management of a control system, CEC (Consumer Electronics Control) over the HDMI connections can control the source and display devices, potentially eliminating the need for dedicated serial cables or IR emitters. CEC over the HDMI outputs can also enable the display devices to be turned on or off automatically without the use of a control system.
Enterprise-Grade Security
The HD-MD4X4-4KZ-E includes advanced security features and protocols. Using 802.1X authentication, Active Directory® credential management, PKI authentication, TLS, SSH, and HTTPS, the HD-MD4X4-4KZ-E provides a true enterprise-grade AV switcher.
Built-In Web Interface
Configuration of the HD-MD4X4-4KZ-E can be accomplished by using the built-in web interface. The configuration of a single unit can be downloaded to a computer or mobile device and then uploaded to multiple HD-MD4X4-4KZ-E units to simplify system installation.
.AV Framework™ Technology Support
In addition to a built-in web interface and control system programming, built-in .AV Framework technology of a Crestron control system can be used to configure and control the HD-MD4X4-4KZ-E. For information about .AV Framework technology and the supported Crestron control systems, visit www.crestron.com/avframework.
XiO Cloud® Service Support
The HD-MD4X4-4KZ-E is compatible with the XiO Cloud service, which is an IoT (Internet of Things) platform for remotely provisioning, monitoring, and managing Crestron devices across an enterprise or an entire client base. Built on the Microsoft® Azure® software platform and using industry-leading Azure IoT Hub technology, the XiO Cloud service enables installers and IT managers to deploy and manage thousands of devices in the amount of time it previously took to manage a single device. Unlike other virtual machine-based cloud solutions, Azure services provide unlimited scalability to suit the ever-growing needs of an enterprise. For more information, visit www.crestron.com/xiocloud.
1 RU Rack-Mountable Design
The HD-MD4X4-4KZ-E can be mounted into a 19-inch EIA equipment rack using the included rack ears. The device occupies 1 RU of rack space.
Key Features
4K60 4:4:4 digital AV switcher
HDR10, HDR10+, and Dolby Vision® video formats
Four HDMI® inputs and four HDMI outputs
EDID management
HDCP 2.3 compliance
HDMI audio de-embedding
Device control via CEC
Enterprise-grade security
Built-in web interface
Compatibility with Crestron® 3-Series® or later control systems
.AV Framework™ technology support
XiO Cloud® service support
1 RU rack-mountable design
PoE+ powered device (optional power pack sold separately)
Specs
Video
Input Signal Types HDMI with HDR10, HDR10+, Dolby Vision, Deep Color, 4K60 4:4:4 support1, 2 (DVI and Dual-Mode DisplayPort™ interface compatible3)
Output Signal Types HDMI with HDR10, HDR10+, Dolby Vision, Deep Color, and 4K60 4:4:4 support1, 2 (DVI compatible4)
Switcher 4x4 digital AV switcher
Copy Protection HDCP 2.3
Maximum Resolutions Common resolutions are listed in the following table.
Scan
Type Resolution Frame
Rate Color
Sampling Color
Depth
Progressive 4096x2160 DCI 4K
and 3840x2160 4K UHD 24 Hz 4:4:4 36 bit
30 Hz 4:4:4 36 bit
60 Hz 4:2:2 36 bit
60 Hz 4:4:4 24 bit
2560x1600 WQXGA 60 Hz 4:4:4 36 bit
1920x1080 HD 1080p 60 Hz 4:4:4 36 bit
Interlaced
(Input Only) 1920x1080 HD 1080i 30 Hz 4:4:4 36 bit
NOTE: Custom resolutions that do not exceed 4096 pixels in width and 2160 pixels in height are supported at pixel clock rates up to 600 MHz.
Audio - General
Digital-To-Analog Conversion 24-bit 48 kHz
Frequency Response ±0.5 dB, 20 Hz to 20 kHz
THD+N <0.005%, 1 kHz, 10 dBV
S/N Ratio >95 dB, 10 dBV, 20 Hz to 20 KHz, A-weighted
Crosstalk ≤90 dB, 1 KHz, for multiple inputs only
Stereo Separation ≤80 dB, 20 Hz to 20 kHz
Audio - Source Inputs
Input Signal Type HDMI (Dual-Mode DisplayPort interface compatible3)
Formats Dolby Digital®, Dolby Digital EX, Dolby Digital Plus, Dolby® TrueHD, Dolby Atmos®, DTS®, DTS-ES, DTS 96/24, DTS HD® High Res, DTS-HD Master Audio, DTS:X®, LPCM up to 8 channels
Audio - Digital Output
Output Signal Type HDMI
Formats Dolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS, DTS-ES, DTS 96/24, DTS HD High Res, DTS-HD Master Audio, DTS:X, LPCM up to 8 channels
Source -80 dB to +20 dB adjustment range, plus Mute
Master Volume -80 dB to +20 dB adjustment range, plus Mute
Audio - Analog Line Output
Output Signal Type/Format Stereo 2-channel
Volume Control -80 dB to +20 dB adjustment range, plus Mute, Mono, and Stereo
Communications
Ethernet 100/1000 Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, DHCP, Web browser setup and control, Crestron control system integration, IEEE 802.1X, Secure CIP, Authentication, SSH/SSL, TLS
USB For firmware loading and configuration management and to power a USB powered device
NOTE: USB functionality requires use of the PW-2420RU power pack (sold separately).
HDMI HDCP 2.3, EDID, CEC
Connectors
HDMI IN 1-4 (4) 19-pin Type A connector, female;
HDMI digital video/audio input (DVI and Dual-Mode DisplayPort interface compatible3)
HDMI OUT 1-4 (4) 19-pin Type A connector, female;
HDMI digital video/audio output (DVI compatible4)
AUDIO OUT, AUX 1-2 (2) 5-pin 3.5 mm detachable terminal block;
Balanced/unbalanced stereo line-level audio output;
Output Impedance: <100 Ohms;
Maximum Output Level: 4 Vrms balanced, 2 Vrms unbalanced
LAN PoE+ (1) 8-pin RJ-45 connector, female;
100BASE-TX/1000BASE-T Ethernet port;
IEEE 802.3at Type 2 Class 4 (25.5 W) PoE+ compliant, capable of being powered by PoE+ power sourcing equipment (PSE)5
24VDC 2.5 A (1) 2.1 x 5.5 mm DC power connector;
24 VDC power input;
PW-2420RU power pack (sold separately)
SERVICE (1) USB Type A female;
For firmware loading and configuration management;
Can also provide up to 5 V 500 mA power to a USB powered device
NOTE: USB functionality of the SERVICE port requires use of the PW-2420RU power pack (sold separately).
G (1) 6-32 screw, chassis ground lug
Controls and Indicators
PWR (1) LED. Amber indicates that the device is booting. Green indicates that the device is operational.
INPUT 1-4 (4) Push buttons for manual input selection and (8) LEDs. Green indicates that the corresponding input is routed to an output.
Amber indicates that a source is detected at the corresponding input but is not routed to an output.
OUTPUT 1-4 (4) Push buttons for manual output selection and (4) LEDs. Green indicates that a display or other destination device is detected and the corresponding output is transmitting video. Amber indicates that a display or other destination device is detected but no video isrouted to the corresponding output.
SETUP (1) Red LED and (1) push button for display of IP address on connected HDMI outputs
Ethernet (2) LEDs on RJ-45 LAN connector.
Link status LED: Green indicates that a 100BASE-TX link is established. Amber indicates that a 1000BASE-T link is established.
Ethernet activity LED: Flashing amber indicates Ethernet activity.
Power
PoE+ IEEE 802.3at Type 2 Class 4 (25.5 W) PoE+ compliant, capable of being powered by PoE+ power sourcing equipment (PSE)5
Power Pack (Optional) Input: 1.3 A maximum @ 100-240 VAC, 50/60 Hz;
Output: 2.5 A @ 24 VDC;
Model: PW-2420RU (sold separately)
NOTE: The PW-2420RU power pack is required for USB functionality.
Power Consumption 17 W typical
Environmental
Temperature 32° to 104° F (0° to 40° C)
Humidity 10% to 90% RH (non-condensing)
Heat Dissipation 58 BTU/hr typical
Acoustic Noise 33.55 dBA typical
Construction
Chassis Metal, black finish, vented sides
Mounting 1 RU 19-inch rack-mountable (rack ears included)
Dimensions
Height 1.72 in. (44 mm)
Width 17.33 in. (441 mm) without rack ears
Depth 7.02 in. (179 mm)
Weight
5.15 lb (2.37 kg)