Media Presentation Button Panel B10, White

A 3-gang, 10-button wall mount control panel with customizable backlit labeling, LED feedback, and volume control knob. Single-wire interface via PoE Ethernet or Cresnet®.

Get Custom Programming from 4TEC

Price: $518.00
    Quantity:
    Availability: In Stock
    Usually ships In 24 - 48 hours

    Item #: MP-B10-W

    Description

    The MP-B10 is an enhanced pushbutton control panel designed for installation in a wall or podium. It can be used with any Crestron® control system or presentation switcher, and it provides a perfect complement to any Crestron MPC Media Presentation Controller. Available in white or black, the MP-B10 is constructed to handle the rigors of everyday use in a typical classroom, meeting room, lecture hall, or training facility.

    Its 10 “hard key” buttons can be custom programmed to control any function, such as system power, input source selection, and lighting presets. Audio volume and other parameters are adjustable using the control knob and LED bargraph. Custom backlit labeling of each button is facilitated using an assortment of pre-printed labels or Crestron Engraver software.

    A built-in IR receiver provides a gateway for RC-5 and Crestron compatible IR wireless remotes. An ambient light sensor is also included, which may be programmed to control the MP-B10’s backlight intensity and other customer functions. The MP-B10 can be powered through the network wiring using either Cresnet® or PoE (Power over Ethernet), requiring just one wire for operation.

    Key Features
    • Wall mount pushbutton control panel
    • No programming required with select .AV Framework™ enabled switchers
    • 10 programmable buttons with LED feedback
    • Customizable backlit button labels
    • Volume control knob and LED bargraph
    • Built-in IR receiver and light sensor
    • High-speed Ethernet or Cresnet® communications
    • PoE or Cresnet network powered
    • 3-gang wall box-mountable

    Specifications

    Communications
    Ethernet10/100 Mbps, auto-switching, auto-negotiating, auto-discovery, full/half duplex, DHCP, IEEE 802.3af and 802.3at Type 1 compliant
    Cresnet®Cresnet slave mode
    USBUSB 1.1 device port for computer console (firmware update)
    IRBuilt-in RC-5 compatible IR receiver
    Connectors
    NET(2) sets of (4) captive screw terminals;
    Cresnet slave port with parallel pass-through
    LAN PoE(1) 8-wire RJ45, female;
    10Base-T/100Base-TX Ethernet port, Power over Ethernet compliant
    Computer(1) USB Type B, female (behind front cover);
    USB 1.1 computer console port for firmware update
    Ground(1) flying lead, chassis ground wire
    Controls & Indicators
    Hard Keys(10) Programmable pushbuttons with backlit labeling
    Feedback Indicators(10) Programmable red LEDs (1 per hard key)
    VOLUME(1) Programmable continuous turn rotary encoder
    Bargraph(1) Programmable red 5-segment LED bargraph
    HW-R(1) Recessed miniature pushbutton for hardware reset
    SETUP(1) Recessed miniature pushbutton (behind front cover) for setting up connection with the control system via Cresnet or Ethernet
    LAN PoE (rear)(2) green LEDs, bottom LED indicates link status, top LED indicates Ethernet activity
    Light Sensor
    Photosensor, programmable for auto-dimming of the backlight and other functions
    IR Receiver
    Reception Frequency36 to 38 kHz IR
    FormatsCrestron format, RC-5
    RangeUp to 50 ft line of sight (typical), dependent upon angle, obstructions, IR interference, and IR remote signal strength
    Power Requirements
    Cresnet Power Usage4 Watts (0.17 Amps @ 24 Volts DC)
    Power over EthernetIEEE 802.3at Type 1 (802.3af compatible) Class 2 (6.49W) PoE Powered Device
    Note: If both PoE and Cresnet power are connected, power will be drawn from Cresnet.
    Environmental
    Temperature32° to 104°F (0° to 40°C)
    Humidity10% to 90% RH (non-condensing)
    Heat Dissipation14 BTU/hr
    Enclosure
    FaceplatePlastic, black or white, with polycarbonate label overlay
    ChassisPlastic with metal mounting plate
    MountingMounts in a 3-gang electrical box or mud ring, 2 inch (51 mm) or greater mounting depth recommended
    Dimensions
    Height4.50 in (115 mm)
    Width6.70 in (171 mm)
    Depth2.23 in (57 mm)
    Weight
    17 oz (475 g)

    Ships with these standard button labels